7800 Series Gateway Installation Guide
About this Guide
This guide provides installation, and setup procedures for the 7800 series gateway.
Conventions
Contact Us
Introduction
Identifying the 7800 Series Gateway Equipment
Installation Prerequisites
7800-CTRL=
7800 Series Telcom Units
7800-TMS
7800 N+1 Patch Panel
7800 1+1 Patch Panel
7800 RJ48C Patch Panel
Preventing Electrostatic Discharge Damage
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. This may occur if electronic printed circuit cards are improperly handled and may cause complete or intermittent failure.
|
Always follow ESD prevention procedures when removing and replacing modules:
|
Recommended Reading
This document is written with the assumption that you have a clear understanding of the installation of the equipment described in this document and you are trained to work with the equipment. If you have any technical questions, TelcoBridges TB Support can be reached at the following numbers, or an email can be sent to: support.
- Americas & Europe Technical Support Centre (GMT-05:00, Montreal): Telephone: +1-450-655-8993 x131 or x102
- Asia Technical Support Centre (GMT +08:00, Hong Kong): Telephone: +852-3749-9818
- 24/7 International Support: Telephone: +1-866-438-4703
Installation Preparations
Package Contents
7800-CTRL Gateway Controllers
7800 Series Telecom Unit
7800-TMS Media Switch
7800 N+1 Patch Panel
7800 1+1 Patch Panels
Rack Mounting the 7800 Series Gateway Equipment
Prerequisites
Vertical Placement of the Equipment
Installing the 7800 Series Gateway on an Equipment Rack
7800-CTRL
7800 Telecom Units
7800-TMS
7800 N+1 Patch Panel
7800 1+1 Patch Panel
7800 RJ48C Patch Panel
Installing the 7800-CTRL
Connecting to the 7800 Series Gateway Management Interface
Connecting to the 7800 Series Control Network
Connecting to the Data Network
Powering Up
Connecting to AC Power
Installing the 7800 Series Telecom Units
Connecting to the Control Network
Connecting to the VoIP Network(s)
Connecting to the PSTN
SCSI Interface (T1/E1) for the TMG7800-TE
Standalone Configuration
1+1 Configuration
Dual BNC Interface (DS3) for the TMG7800-DS3
Standalone Configuration
1+1 Configuration
OC3/STM-1 Interface for the TMG7800-STM1
Standalone Configuration
1+1 Configuration
N+1 Configuration
Connecting to the TMS Network
Connecting to the TMG7800 Telecom Units
Prerequisites
Interconnections
Interconnecting Two 7800 Telecom Units
Grounding the Equipment Chassis
Powering Up
Connecting to AC Power
Connecting to DC Power
Installing the 7800-TMS
Connecting to the Control Network
Grounding the Equipment Chassis
7800 TMS
Powering Up
Connecting to AC Power
Connecting to DC Power
TDM System Clock
Installing the 7800 N+1 Patch Panel
Connecting Fiber Optic Cables to the 7800 N+1 Patch Panel
Connecting to the Control Network
Grounding the Equipment Chassis
Connecting to AC Power
Start Up and Verification
Start Up
Verifying the LED Status Indications
7800-CTRL
7800 Telecom Unit
7800-TMS
7800 N+1 Patch Panel
Powering Down the Equipment
7800-CTRL
Local Method
Remote Method
7800 Telecom Unit
7800-TMS
7800 N+1 Patch Panel
Initial System Configuration
7800 Series Gateway SSH Connection
7800 Series Gateway Serial Connection
Connecting to the 7800-CTRL Console
Configuring the Terminal Emulator Application
Changing the 7800 Series Gateway Management Port IP Address
Retrieving 7800 Series Gateway Information
Changing 7800 Series Gateway Management Port Passwords
Configuring the 7800 Series Gateway Using the Web Portal
System Backups
Creating a Database Backup
Downloading a Database Backup
Uploading a Database Backup
Restoring a Database Backup
Wiring Diagrams
RJ48C Wiring Diagram: Crossover and Straight Cables
RJ48 Console Wiring Diagram