AllynSandbox
About this Guide
This guide provides installation, and setup procedures for 800 series standalone and 800 series 1+1 systems.
Conventions
| Terminology | Description |
|---|---|
| 800 series gateway | This term is used when a description applies to both the 800 series standalone and
800 series 1+1 system. |
| 800 series standalone | This term is used when a description applies to the 800 series unit operating as a
standalone unit. |
| 800 series 1+1 System | This term is used when a description applies to the 800 series unit operating in
conjunction with the 800+1 series unit. This term also includes the 1+1 patch panel. |
| 800 series unit | This term is used when a description applies to all variations of the 800 series units,
such as: TMG800, TSG800, and TMGIP800. |
| 800 series +1 unit | This term is used when a description applies to all variations of the 800 series +1
units, such as TMG800 +1, TSG800 +1, or TMGIP800 +1. |
| 1+1 Patch Panel | This term is used as a generic reference to a 1+1 patch panel, which enables an 800
series unit to connect to an 800 series +1 unit. |
To help guide you in the installation of your product, we use the following icons in this document. Take note of the icon that represents the type of installation you are conducting and follow those procedures throughout this guide to ensure proper equipment installation and set up.
| Graphic | Description |
|---|---|
 |
This icon appears in the margins of pages describing the 800 series operating as a
standalone unit. If you are installing a standalone unit, read and follow the instructions provided in those sections. |
 |
This icon appears in the margins of pages describing the 800 series unit operating in
conjunction with an 800 series +1 and 1+1 patch panel. If you are installing a 1+1 system read and follow the instructions provided in those sections and pages. |
Contact Us
If you have comments about this guide or any other TelcoBridges technical documentation, please send an email to marketing.
Introduction
This section provides an introduction of the installation and setup for the following system configurations:
- 800 Series Standalone: Single gateway unit operating in standalone mode.
- 800 series 1+1 system: 800 series unit operating in conjunction with an 800 series +1 unit and 1+1 patch panel(s).
Recognizing an 800 Series Standalone versus an 800 Series 1+1 System
800 Series Standalone
The 800 series standalone consists of one telecom unit.
800 Series 1+1 System
The 800 series 1+1 system, see figure 1.1 on page 2, consists of:
- One telecom unit
- One +1 telecom unit
- One or two 1+1 patch panels
Equipment Front and Rear Views
Installation Prerequisites
For the installation to proceed without interruption, it is important that you have all necessary materials on hand.
| 800 Series Standalone | 800 Series 1+1 System |
|---|---|
| Adequate space for the installation of the 800 series standalone.
You will need to mount the 800 series unit on a 19" equipment rack (customer provided). Your 800 series unit is a 1U unit. | Adequate space for the installation of the 800 series standalone. You will need to mount the 800 series unit on a 19" equipment rack (customer provided). Your 800 series unit is a 1U unit. The 1+1 System requires space for the following number of units: 800 Series Unit: 1U 800 Series +1 Unit: 1U 1+1 Patch Panel(s): 1U/2U Total: 3U/4U | |
| Adequate power supply and power connections.
The 800 series unit requires two power connections. To guarantee an uninterrupted supply of electricity, each power connection must be fed by a dedicated power source.| Adequate power supply and power connections. The 800 series and 800 series +1 units require two power connections each. To guarantee an uninterrupted supply of electricity, each power connection must be fed by a dedicated power source. | |
| IP addresses for the management ports.
To avoid delays, you should have the IP address, netmask and gateway addresses on hand. Take note that the management port supports DHCP, see Connecting to the 800 Series Gateway Management Interface, for further information. | Adequate space for the installation of the 800 series 1+1 system. You will need to mount the 800 series 1+1 system on a 19" equipment rack (customer provided).| IP addresses for the management ports. To avoid delays, you should have the IP address, netmask and gateway addresses on hand. Take note that the management port supports DHCP, see Connecting to the 800 Series Gateway Management Interface for further information. |