Configuring IP Interfaces: Difference between revisions
No edit summary |
(Added Steps 5 and 6) |
||
| Line 1: | Line 1: | ||
The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following: | The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following: | ||
*IP Address | *IP Address | ||
*Netmask | *Netmask | ||
*Gateway | *Gateway | ||
<br | <br> | ||
== To configure a VoIP0 or VoIP1 port == | == To configure a VoIP0 or VoIP1 port == | ||
1. Select '''IP Interfaces''' from the navigation panel: | 1. Select '''IP Interfaces''' from the navigation panel: | ||
[[Image: | [[Image:Toolpack v2.5 Navigation Panel IP Interfaces.png]] | ||
<br | <br> 2. Click '''Edit''' from the IP Interfaces Information panel: | ||
2. Click '''Edit''' from the IP Interfaces Information panel: | |||
[[Image: | [[Image:Toolpack v2.5 Edit IP Interface.png]] | ||
<br | <br> 3. Configure the IP port: | ||
3. Configure the IP port: | |||
* Indicate whether or not to use '''DHCP''' on this port | *Indicate whether or not to use '''DHCP''' on this port | ||
* Enter an '''IP address''' | *Enter an '''IP address''' | ||
* Enter a '''Netmask''' | *Enter a '''Netmask''' | ||
* Enter a '''gateway address''' | *Enter a '''gateway address''' | ||
* Click '''Save''' | *Click '''Save''' | ||
'''Note:''' The IP addresses of ETH0, ETH1, VOIP0 and VOIP1 must be on different subnets. | '''Note:''' The IP addresses of ETH0, ETH1, VOIP0 and VOIP1 must be on different subnets. <br> | ||
<br | |||
[[Image: | [[Image:Toolpack v2.5 Editing IP Interface.png]] | ||
<br | <br> | ||
4. The changes are displayed in the IP interfaces information panel: | 4. The changes are displayed in the IP interfaces information panel: | ||
[[Image: | [[Image:Toolpack v2.5 IP Interface Edited.png]] | ||
<br> '''IMPORTANT!''' The system will display the following notice, describing steps to apply your new configuration: | |||
[[Image:Toolpack v2.5 IP Interface Alert.png]] | |||
<br> | |||
5. Activate the configuration | |||
Systems -> Edit -> Activate | |||
6. Reboot the adapter (will drop active calls) | |||
Status -> Adapters -> Click on the adapter Serial Number -> Reboot adapter | |||
It will take about 1.5 minutes to restart the unit. | |||
==List of Parameters== | == List of Parameters == | ||
* [[Parameter: Use DHCP|Use DHCP]] | *[[Parameter: Use DHCP|Use DHCP]] | ||
* [[Parameter: IP Address|IP Address]] | *[[Parameter: IP Address|IP Address]] | ||
* [[Parameter: Netmask|Netmask]] | *[[Parameter: Netmask|Netmask]] | ||
* [[Parameter: Gateway|Gateway]] | *[[Parameter: Gateway|Gateway]] | ||
Revision as of 20:58, 8 June 2011
The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following:
- IP Address
- Netmask
- Gateway
To configure a VoIP0 or VoIP1 port
1. Select IP Interfaces from the navigation panel:
2. Click Edit from the IP Interfaces Information panel:
3. Configure the IP port:
- Indicate whether or not to use DHCP on this port
- Enter an IP address
- Enter a Netmask
- Enter a gateway address
- Click Save
Note: The IP addresses of ETH0, ETH1, VOIP0 and VOIP1 must be on different subnets.
4. The changes are displayed in the IP interfaces information panel:
IMPORTANT! The system will display the following notice, describing steps to apply your new configuration:
5. Activate the configuration
Systems -> Edit -> Activate
6. Reboot the adapter (will drop active calls)
Status -> Adapters -> Click on the adapter Serial Number -> Reboot adapter
It will take about 1.5 minutes to restart the unit.