Actions

Use Cases:Network Configuration A: Difference between revisions
Line 33: Line 33:


*When you [[Toolpack:Configuring_VoIP_Interfaces C|Create an IP Address]], configure it as follows:
*When you [[Toolpack:Configuring_VoIP_Interfaces C|Create an IP Address]], configure it as follows:
**Name: VOIP_UNTAG
**'''Name''': VOIP_UNTAG
**Virtual Ports: vp VOIP U
**'''Virtual Ports''': vp VOIP U
**IP Address: x.x.x.y
**'''IP Address''': x.x.x.y
**Services: RTP, SIP, SIGTRAN
**'''Services''': RTP, SIP, SIGTRAN


|-
|-
Line 52: Line 52:
|  
|  
*When you [[Toolpack:Protocol_Stack_Settings_A#H.248 MEGACO|Configure H.248]], set the following:
*When you [[Toolpack:Protocol_Stack_Settings_A#H.248 MEGACO|Configure H.248]], set the following:
**Local IP Address and Public IP Address: x.x.x.x [Public IP orNAT public IP]
**'''Local IP Address and Public IP Address''': x.x.x.x [Public IP orNAT public IP]


|  
|  
*When you [[Toolpack:CDR_Settings_A|Configure RADIUS]], set the following:
*When you [[Toolpack:CDR_Settings_A|Configure RADIUS]], set the following:
**Source IP interface: Any
**'''Source IP interface''': Any
**Radius -> Radius Server
**'''Radius -> Radius Server'''
**Public IP Address: Empty
**'''Public IP Address''': Empty
|}
|}
|}
|}

Revision as of 16:09, 23 April 2015

Applies to version(s): v2.8.

This article provides the steps required to complete the most common IP network configurations using the Web Portal.

One subnet, Two IP Addresses, Untagged

Note:
A TMG3200 in a tagged configuration can use eth0 and eth1.
VoipO/Voip1 bonding is optional.
Configure IP Network A Configure IP Network B

Subnet A uses the MGMT0 network interface; because it is untagged its IP can only be configured with the tbchangeip command on the SSH port.

Subnet B is untagged and bonded over VOIP0 and VOIP1 ports.



  • When you Create an IP Address, configure it as follows:
    • Name: VOIP_UNTAG
    • Virtual Ports: vp VOIP U
    • IP Address: x.x.x.y
    • Services: RTP, SIP, SIGTRAN
Configure SIP Configure SIGTRAN Configure H.248 Configure RADIUS
  • When you Configure H.248, set the following:
    • Local IP Address and Public IP Address: x.x.x.x [Public IP orNAT public IP]
  • When you Configure RADIUS, set the following:
    • Source IP interface: Any
    • Radius -> Radius Server
    • Public IP Address: Empty

Two subnets, One IP per subnet, untagged

[image of network configuration 2]

Configure IP Network A Configure IP Network B

Subnet A uses the MGMT0 network interface; because it is untagged its IP can only be configured with the tbchangeip command on the SSH port.

Subnet B is untagged and is bonded over VOIP0 and VOIP1 ports.

Configure SIP Configure SIGTRAN Configure H.248 Configure RADIUS

Two VLAN, Three IP Address, tagged

[image of network configuration 3]

Configure IP Network A Configure IP Network B

Subnet B uses untag bonded over VOIP0 and VOIP1 ports

Configure SIP Configure SIGTRAN Configure H.248 Configure RADIUS
Retrieved from "https://docs.telcobridges.com/w/index.php?title=Use_Cases:Network_Configuration_A&oldid=18216"