Actions

Use Cases:Network Configuration A: Difference between revisions
Line 26: Line 26:




When you [[Toolpack:Configuring_Virtual_Port A|Create an IP Virtual Port]], configure it as follows:
*When you [[Toolpack:Configuring_Virtual_Port A|Create an IP Virtual Port]], configure it as follows:
*Name: vp VOIP U
**Name: vp VOIP U
*vLanId: Untagged
**vLanId: Untagged
*Physical Ports: voip0, voip1
**Physical Ports: voip0, voip1




When you [[Toolpack:Configuring_VoIP_Interfaces C|Create an IP Address]], configure it as follows:
*When you [[Toolpack:Configuring_VoIP_Interfaces C|Create an IP Address]], configure it as follows:
*Name: VOIP_UNTAG
**Name: VOIP_UNTAG
*Virtual Ports: vp VOIP U
**Virtual Ports: vp VOIP U
*IP Address: x.x.x.y
**IP Address: x.x.x.y
*Services: RTP, SIP, SIGTRAN
**Services: RTP, SIP, SIGTRAN


|-
|-
Line 51: Line 51:
*[[Toolpack:Protocol_Stack_Settings_A#H.248 MEGACO|Configure SIGTRAN]]
*[[Toolpack:Protocol_Stack_Settings_A#H.248 MEGACO|Configure SIGTRAN]]
|  
|  
When you [[Toolpack:Protocol_Stack_Settings_A#H.248 MEGACO|Configure H.248]], make the following specific settings:
*When you [[Toolpack:Protocol_Stack_Settings_A#H.248 MEGACO|Configure H.248]], set the following:
* Local IP Address and Public IP Address: x.x.x.x [Public IP orNAT public IP]
**Local IP Address and Public IP Address: x.x.x.x [Public IP orNAT public IP]


|  
|  
*[[Configure RADIUS]]
*When you [[Toolpack:CDR_Settings_A|Configure RADIUS]], set the following:
**Source IP interface: Any
**Radius -> Radius Server
**Public IP Address: Empty
|}
|}
|}
|}

Revision as of 16:06, 23 April 2015

Applies to version(s): v2.8.

This article provides the steps required to complete the most common IP network configurations using the Web Portal.

One subnet, Two IP Addresses, Untagged

Note:
A TMG3200 in a tagged configuration can use eth0 and eth1.
VoipO/Voip1 bonding is optional.
Configure IP Network A Configure IP Network B

Subnet A uses the MGMT0 network interface; because it is untagged its IP can only be configured with the tbchangeip command on the SSH port.

Subnet B is untagged and bonded over VOIP0 and VOIP1 ports.



  • When you Create an IP Address, configure it as follows:
    • Name: VOIP_UNTAG
    • Virtual Ports: vp VOIP U
    • IP Address: x.x.x.y
    • Services: RTP, SIP, SIGTRAN
Configure SIP Configure SIGTRAN Configure H.248 Configure RADIUS
  • When you Configure H.248, set the following:
    • Local IP Address and Public IP Address: x.x.x.x [Public IP orNAT public IP]
  • When you Configure RADIUS, set the following:
    • Source IP interface: Any
    • Radius -> Radius Server
    • Public IP Address: Empty

Two subnets, One IP per subnet, untagged

[image of network configuration 2]

Configure IP Network A Configure IP Network B

Subnet A uses the MGMT0 network interface; because it is untagged its IP can only be configured with the tbchangeip command on the SSH port.

Subnet B is untagged and is bonded over VOIP0 and VOIP1 ports.

Configure SIP Configure SIGTRAN Configure H.248 Configure RADIUS

Two VLAN, Three IP Address, tagged

[image of network configuration 3]

Configure IP Network A Configure IP Network B

Subnet B uses untag bonded over VOIP0 and VOIP1 ports

Configure SIP Configure SIGTRAN Configure H.248 Configure RADIUS
Retrieved from "https://docs.telcobridges.com/w/index.php?title=Use_Cases:Network_Configuration_A&oldid=18214"