Use Cases:Network Configuration IP UseCase6 A: Difference between revisions

Revision as of 03:25, 28 September 2016

Configure IP Network
Configure IP Address & Virtual Port. Create Virtual Port Create IP Address Virtual Port Configuration: 1. Name: GW_Internal: VLan ID: 3999 Physical Port: Voip0, Voip1 Note: It is recommended to use vLan ID 3999 for the internal network (not required on the external switches). 2. Name: Public_IP_VLan250: VLan ID: 250 Port: Voip0, Voip1 Note: This is the external network vLan that must be configured on the external switch. IP Interface Configuration: 1. Name: GW_Internal Virtual Port: GW_Internal IP Address: 192.168.217.1 Subnet mask: 255.255.255.0 Gateway: 192.168.217.1 Service: Management 2. Name: Radius Internal Virtual Port: GW_Internal IP Address: 192.168.217.2 Subnet mask: 255.255.255.0 Gateway: 192.168.217.1 Service: H.248 / Radius 3. Name: Voip_Internal Virtual Port: GW_Internal IP Address: 192.168.217.3 Subnet mask: 255.255.255.0 Gateway: 192.168.217.1 Service: RTP, SIP, Sigtran. 4. Name: All_Public_250 Virtual Port: Public_IP_VLan250 IP Address: X.X.X.X (Public IP Address) Subnet mask: 255.255.255.0 Gateway: X.X.X.X Service: Management (Notes: We have to put management , but is used for all services)

Configure NAT
NAT Configuration: Advanced Networking -> NATs -> Create New Internal NAT Name: Internal NAT Local Gateway IP Interface:[Unit]:GW_INTERNAL Public Interface: [Unit]:ALL_PUBLIC_250 Advanced Networking -> NATs -> Create New NAT Traversal Name: PUBLIC_IP Method:Force Public IP Public IP Address: X.X.X.X [Public IP] Create Virtual Port Create IP Address

Configure SIP	Configure SIGTRAN	Configure H.248	Configure RADIUS
Configure SIP IP range parameters: Name: PORT_RANGE_VOIP IP Interface: VOIP_ADDRESS Minimum Port: 20000 Maximum Port: 30000 SIP transport server parameters: Port: 5060 IP Interface: VOIP_ADDRESS SIP NAP parameters: Proxy Address: X.X.X.X Port Range: PORT_RANGE_VOIP	Configure SIGTRAN	When you Configure H.248, set the following: Local IP Address and Public IP Address: X.X.X.X [Public IP or NAT public IP]	When you Configure RADIUS, set the following: Source IP interface: RADIUS_100 Radius -> Radius Server Public IP Address: Empty

@@ Line 15: / Line 15: @@
 |
 Configure IP Address & Virtual Port.
-*[[Create Virtual Port]]
+*[[Toolpack:Configuring_Virtual_Port_A|Create Virtual Port]]
-*[[Create IP Address]]
+*[[Toolpack:Configuring_VoIP_Interfaces_C|Create IP Address]]
 *Virtual Port Configuration:
@@ Line 29: / Line 29: @@
 *IP Interface Configuration:
 **1. Name: GW_Internal
 ***'''Virtual Port''': GW_Internal
@@ Line 36: / Line 35: @@
 ***'''Gateway''': 192.168.217.1
 ***'''Service''': Management
 **2. Name: Radius Internal
 ***'''Virtual Port''': GW_Internal
@@ Line 43: / Line 41: @@
 ***'''Gateway''': 192.168.217.1
 ***'''Service''': H.248 / Radius
 **3. Name: Voip_Internal
 ***'''Virtual Port''': GW_Internal
@@ Line 50: / Line 47: @@
 ***'''Gateway''': 192.168.217.1
 ***'''Service''': RTP, SIP, Sigtran.
 **4. Name: All_Public_250
 ***'''Virtual Port''': Public_IP_VLan250
@@ Line 64: / Line 60: @@
 |
 *NAT Configuration:
 **Advanced Networking -> NATs -> Create New Internal NAT
 ***'''Name''': Internal NAT
 ***'''Local Gateway IP Interface''':[Unit]:GW_INTERNAL
 ***'''Public Interface''': [Unit]:ALL_PUBLIC_250
 **Advanced Networking -> NATs -> Create New NAT Traversal
 ***'''Name''': PUBLIC_IP
 ***''' Method''':Force Public IP
 ***'''Public IP Address''': X.X.X.X [Public IP]
+*[[Toolpack:Configuring_Virtual_Port_A|Create Virtual Port]]
-*[[Create_NAT_Traversal_B]]
+*[[Toolpack:Configuring_VoIP_Interfaces_C|Create IP Address]]
-*[[Create_Internal_NAT_B]]
 |-
 |}