Use Cases:HW Transcoding Configuration UseCase1 A: Difference between revisions

Latest revision as of 12:16, 3 January 2025

This article applies to:	Product	Version
This article applies to:	SBC	3.1, 3.3

Perequisites

ProSBC (or Tsbc) Host

Network device name    Network device role    Network Config
-------------------    -------------------    -------------------
mgmt0                  mgmt                   Untagged
wan0                   LAN/WAN                Tagged 1650
lan0                   LAN/WAN                Tagged 1651
trans0                 LAN/WAN                Tagged 752     
trans1                 LAN/WAN                Tagged 753     
ctrl0                  ctrl0                  Tagged 750
ctrl1                  ctrl1                  Tagged 751

NOTE: The 'Network device names' for transcoding must be trans0 and trans1

Hardware Unit - TB002177 is the TSBC-HW-TRANS unit in the below setup

 Network device name    Network device role    Network Config
-------------------    -------------------    -------------------
voip0                   LAN/WAN                Tagged 752
voip1                   LAN/WAN                Tagged 753
eth0                    ctrl0                  Untagged PVID 750  **
eth1                    ctrl1                  Untagged PVID 751  **

NOTE: On the network switch, the control ports on the Hardware unit need to be configure with Link Type: Access

Two subnet, Two IP Addresses, tagged

Network configuration

Configure IP Network for wan0	Configure IP Network for lan0	Configure IP Network for trans0	Configure IP Network for trans1
Create vp_wan0 virtual port: Name: vp_wan0 Ethernet Ports: wan0 VLAN name: vlan_1650 VLAN id: 1650 Create wan0 IP Address: Name: wan0 Service to use: RTP, SIP Host VLAN: vp_wan0:vlan_1650 IP address: 192.168.150.1 Netmask: 255.255.255.0	Create vp_lan0 virtual port: Name: vp_lan0 Ethernet Ports: lan0 VLAN name: vlan_1651 VLAN id: 1651 Create lan0 IP Address: Name: lan0 Service to use: RTP, SIP Host VLAN: vp_lan0:vlan_1651 IP address: 192.168.151.1 Netmask: 255.255.255.0	Create vp_trans0 virtual port: Name: vp_trans0 Ethernet Ports: trans0 VLAN name: vlan_752 VLAN id: 752 Create trans0 IP Address: Name: trans0 Service to use: RTP Host VLAN: vp_trans0:vlan_752 IP address: 192.168.152.1 Netmask: 255.255.255.0	Create vp_trans1 virtual port: Name: vp_trans1 Ethernet Ports: trans1 VLAN name: vlan_753 VLAN id: 753 Create trans1 IP Address: Name: trans1 Service to use: RTP Host VLAN: vp_trans1:vlan_753 IP address: 192.168.153.1 Netmask: 255.255.255.0

Transcoding unit configuration

Add transcoding unit
Show transcoding unit Add TB002177 transcoding unit

Transcoding unit network configuration

Configure IP Network for voip0	Configure IP Network for voip1
Modify voip0 virtual port: Name: voip0 Untagged: unselect VLAN id: 752 Modify voip0 IP Address: Interface Name: voip0 Service to use: RTP Virtual port: TB002177:voip0 IP address: 192.168.152.10 Netmask: 255.255.255.0	Modify voip1 virtual port: Name: voip1 Untagged: unselect VLAN id: 753 Modify voip1 IP Address: Interface Name: voip1 Service to use: RTP Virtual port: TB002177:voip1 IP address: 192.168.153.10 Netmask: 255.255.255.0

Sip configuration

Configure SIP
Configure SIP For WAN0 RTP port ranges parameters: Name: pr_wan0 IP Interface: vlan_1650:wan0 RTP Port min: 20000 RTP Port max: 40000 SIP transport server parameters: Name: ts_wan0 Port: 5060 IP Interface: vlan_1650:wan0 SIP NAP parameters: Name: nap_sip_wan0 Proxy Address: 192.168.150.10 Port Range: vlan_1650:wan0:pr_wan0:20000-40000 SIP Transport Servers: ts_wan0 For LAN0 RTP port ranges parameters: Name: pr_lan0 IP Interface: vlan_1651:lan0 RTP Port min: 20000 RTP Port max: 40000 SIP transport server parameters: Name: ts_lan0 Port: 5060 IP Interface: vlan_1651:lan0 SIP NAP parameters: Name: nap_sip_lan0 Proxy Address: 192.168.151.10 Port Range: vlan_1651:lan0:pr_lan0:20000-40000 SIP Transport Servers: ts_lan0

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s): v3.0, v3.1''''' ===
+{{DISPLAYTITLE:IP Transcoding Unit Configuration Use Case:Two subnet, Two IP Addresses, tagged}}
-{{DISPLAYTITLE:IP Transcoding Unit Configuration Use Case:Two subnet, Two IP Addresses, tagged}}
+{| class="wikitable"
-__TOC__
+|-
+|rowspan="2"|This article applies to:
+|'''Product'''
+|'''Version'''
+|-
+|SBC
+|3.1, 3.3
+|}
@@ Line 9: / Line 16: @@
 |STYLE="vertical-align: top"|
 {| border="1" class="wikitable"
-! width="500" style="background: none repeat scroll 0% 0% rgb(0, 83, 139);" | Perequisites
+! width="600" style="background: none repeat scroll 0% 0% rgb(0, 83, 139);" | Perequisites
 |-
 |
-*ProSBC Host
+*ProSBC (or Tsbc) Host
   Network device name    Network device role    Network Config
   -------------------    -------------------    -------------------
@@ Line 18: / Line 25: @@
   wan0                   LAN/WAN                Tagged 1650
   lan0                   LAN/WAN                Tagged 1651
   trans0                 LAN/WAN                Tagged 752
   trans1                 LAN/WAN                Tagged 753
   ctrl0                  ctrl0                  Tagged 750
   ctrl1                  ctrl1                  Tagged 751
+'''NOTE:''' The 'Network device names' for transcoding must be trans0 and trans1
 *Hardware Unit - TB002177 is the TSBC-HW-TRANS unit in the below setup
    Network device name    Network device role    Network Config
@@ Line 30: / Line 39: @@
   eth1                    ctrl1                  Untagged PVID 751  **
+'''NOTE:''' On the network switch, the control ports on the Hardware unit need to be configure with Link Type: Access
 |-
 |}
-** Note: On the network switch, the control ports on the Hardware unit need to be configure with Link Type: Access
 == Two subnet, Two IP Addresses, tagged ==
 [[File:UseCase_TsbcHwTranscoding.png|link=]]
 == Network configuration ==