Modify Fax Relay Profile C: Difference between revisions
| Line 27: | Line 27: | ||
==List of Parameters== | ==List of Parameters== | ||
Fax/Modem Relay | Fax/Modem Relay | ||
* [[Parameter: Fax Modem Relay: Enable Fax/Modem Relay| | * [[Parameter: Fax Modem Relay: Enable Fax/Modem Relay|Enable Fax/Modem Relay]] | ||
* [[Parameter: Fax Modem Relay: Detection Mode| | * [[Parameter: Fax Modem Relay: Detection Mode|Detection Mode]] | ||
* [[Parameter: Fax Modem Relay: Relay Mode| | * [[Parameter: Fax Modem Relay: Relay Mode|Relay Mode]] | ||
* [[Parameter: Fax Modem Relay: Modem vs. Fax distinction timeout| | * [[Parameter: Fax Modem Relay: Modem vs. Fax distinction timeout|Modem vs. Fax distinction timeout]] | ||
* [[Parameter: Fax Modem Relay: Fax/Modem tones detection duration| | * [[Parameter: Fax Modem Relay: Fax/Modem tones detection duration|Fax/Modem tones detection duration]] | ||
* [[Parameter: Fax Modem Relay: Enable early Fax/Modem tone detection| | * [[Parameter: Fax Modem Relay: Enable early Fax/Modem tone detection|Enable early Fax/Modem tone detection]] | ||
* [[Parameter: Fax Modem Relay: Enable switching to FAX relay upon CNG tone| | * [[Parameter: Fax Modem Relay: Enable switching to FAX relay upon CNG tone|Enable switching to FAX relay upon CNG tone]] | ||
* [[Parameter: Fax Modem Relay: Switch to passthrough upon Bell ANS| | * [[Parameter: Fax Modem Relay: Switch to passthrough upon Bell ANS|Switch to passthrough upon Bell ANS]] | ||
<br> | <br> | ||
T.38 Parameters | T.38 Parameters | ||
* [[Parameter: T.38 Parameters: Use V.34| | * [[Parameter: T.38 Parameters: Use V.34|Use V.34]] | ||
* [[Parameter: T.38 Parameters: Maximum Bit Rate| | * [[Parameter: T.38 Parameters: Maximum Bit Rate|Maximum Bit Rate]] | ||
* [[Parameter: T.38 Parameters: Fill Bit Removal| | * [[Parameter: T.38 Parameters: Fill Bit Removal|Fill Bit Removal]] | ||
* [[Parameter: T.38 Parameters: Redundancy Count| | * [[Parameter: T.38 Parameters: Redundancy Count|Redundancy Count]] | ||
* [[Parameter: T.38 Parameters: Transmission level (-1dBm unit)| | * [[Parameter: T.38 Parameters: Transmission level (-1dBm unit)|Transmission level (-1dBm unit)]] | ||
<br> | <br> | ||
Fax/Modem Pass-through Parameters | Fax/Modem Pass-through Parameters | ||
* [[Parameter: Fax Modem Pass-Through Parameters: Detection Type| | * [[Parameter: Fax Modem Pass-Through Parameters: Detection Type|Detection Type]] | ||
* [[Parameter: Fax Modem Pass-Through Parameters: Codec| | * [[Parameter: Fax Modem Pass-Through Parameters: Codec|Codec]] | ||
* [[Parameter: Fax Modem Pass-Through Parameters: Jitter Buffer Depth| | * [[Parameter: Fax Modem Pass-Through Parameters: Jitter Buffer Depth|Jitter Buffer Depth]] | ||
* [[Parameter: Fax Modem Pass-Through Parameters: Packet Duration| | * [[Parameter: Fax Modem Pass-Through Parameters: Packet Duration|Packet Duration]] | ||
* [[Parameter: Fax Modem Pass-Through Parameters: Use NSE| | * [[Parameter: Fax Modem Pass-Through Parameters: Use NSE|Use NSE]] | ||
* [[Parameter: Fax Modem Pass-Through Parameters: Support V.152 VBD| | * [[Parameter: Fax Modem Pass-Through Parameters: Support V.152 VBD|Support V.152 VBD]] | ||
* [[Parameter: Fax Modem Pass-Through Parameters: Force V.152 VBD| | * [[Parameter: Fax Modem Pass-Through Parameters: Force V.152 VBD|Force V.152 VBD]] | ||
Latest revision as of 11:41, 28 September 2015
Applies to version v2.8
To configure FAX Relay settings, do the following:
1- Click Fax Relay in the Editing Profile window, to display the customizable options.
2- Modify settings as required.
3- To configure NSE, check the Use NSE checkbox.
NOTE:
If NSE exchange is possible (negociated in the SDP), the switch to passthrough will happen in the RTP stream and no longer wiil occur with a SIP re-INVITE. This implementation of NSE currently only supports a switch to passthrough, which means that you can have NSE packets switching to T.38.
- Click Save
List of Parameters
Fax/Modem Relay
- Enable Fax/Modem Relay
- Detection Mode
- Relay Mode
- Modem vs. Fax distinction timeout
- Fax/Modem tones detection duration
- Enable early Fax/Modem tone detection
- Enable switching to FAX relay upon CNG tone
- Switch to passthrough upon Bell ANS
T.38 Parameters
Fax/Modem Pass-through Parameters