Actions

Use Cases:HW Transcoding Configuration UseCase1 A: Difference between revisions

(Added configuration steps for HW Transcoding)
No edit summary
 
(29 intermediate revisions by 4 users not shown)
Line 1: Line 1:
=== '''''Applies to version(s): v3.0''''' ===
{{DISPLAYTITLE:IP Transcoding Unit Configuration Use Case:Two subnet, Two IP Addresses, tagged}}
{{DISPLAYTITLE:IP HW Transcoding Configuration Use Case:Two subnet, Two IP Addresses, tagged}}
__TOC__


== Two subnet, Two IP Addresses, tagged ==
{| class="wikitable"
|-
|rowspan="2"|This article applies to:
|'''Product'''
|'''Version'''
|-
|SBC
|3.1, 3.3
|}


[[File:UseCase_TsbcHwTranscoding_0.png|link=]]


== Perequisites ==
{|
{|
|STYLE="vertical-align: top"|
|STYLE="vertical-align: top"|
{| border="1" class="wikitable"
{| border="1" class="wikitable"
! width="500" style="background: none repeat scroll 0% 0% rgb(0, 83, 139);" | Perequisites
! width="600" style="background: none repeat scroll 0% 0% rgb(0, 83, 139);" | Perequisites
|-
|-
|
|
*Host
*ProSBC (or Tsbc) Host
  Network device name    Network device role
  Network device name    Network device role   Network Config
  -------------------    -------------------
  -------------------    -------------------    -------------------
  mgmt0                  mgmt
  mgmt0                  mgmt                   Untagged
  wan0                  LAN/WAN
  wan0                  LAN/WAN               Tagged 1650
  lan0                  LAN/WAN
  lan0                  LAN/WAN               Tagged 1651
  trans0                LAN/WAN
  trans0                LAN/WAN               Tagged 752   
  trans1                LAN/WAN
  trans1                LAN/WAN               Tagged 753   
  ctrl0                  ctrl0
  ctrl0                  ctrl0                 Tagged 750
  ctrl1                  ctrl1
  ctrl1                  ctrl1                 Tagged 751           
*Hardware unit
'''NOTE:''' The 'Network device names' for transcoding must be trans0 and trans1
  TSBC-HW-TRANS
 
*Hardware Unit - TB002177 is the TSBC-HW-TRANS unit in the below setup
  Network device name    Network device role    Network Config
  -------------------    -------------------    -------------------
voip0                  LAN/WAN                Tagged 752
voip1                  LAN/WAN                Tagged 753
eth0                    ctrl0                  Untagged PVID 750  **
eth1                    ctrl1                  Untagged PVID 751  **
 
'''NOTE:''' On the network switch, the control ports on the Hardware unit need to be configure with Link Type: Access
|-
|-
|}
|}


== Two subnet, Two IP Addresses, tagged ==
[[File:UseCase_TsbcHwTranscoding.png|link=]]
== Network configuration ==
{|
{|
|STYLE="vertical-align: top"|
|STYLE="vertical-align: top"|
Line 75: Line 95:
*Create [[Toolpack:Configuring_IP_Interface_SBC_A|trans0 IP Address]]:
*Create [[Toolpack:Configuring_IP_Interface_SBC_A|trans0 IP Address]]:
**'''Name''': trans0
**'''Name''': trans0
**'''Service to use''': RTP, SIP
**'''Service to use''': RTP
**'''Host VLAN''': vp_trans0:vlan_752
**'''Host VLAN''': vp_trans0:vlan_752
**'''IP address''': 192.168.152.1
**'''IP address''': 192.168.152.1
Line 90: Line 110:
*Create [[Toolpack:Configuring_IP_Interface_SBC_A|trans1 IP Address]]:
*Create [[Toolpack:Configuring_IP_Interface_SBC_A|trans1 IP Address]]:
**'''Name''': trans1
**'''Name''': trans1
**'''Service to use''': RTP, SIP
**'''Service to use''': RTP
**'''Host VLAN''': vp_trans1:vlan_753
**'''Host VLAN''': vp_trans1:vlan_753
**'''IP address''': 192.168.153.1
**'''IP address''': 192.168.153.1
Line 97: Line 117:
|-
|-
|}
|}
== Transcoding unit configuration ==
{| colspan="4" border="1" class="wikitable"
! width="250" style="background: none repeat scroll 0% 0% rgb(0, 83, 139);" | Add transcoding unit
|-
|
*Show [[Toolpack:Show_Hardware_Units_A|transcoding unit]]
*Add [[Toolpack:Adding_a_Transcoding_Unit_A|TB002177 transcoding unit]]
|}
== Transcoding unit network configuration ==
{|
|STYLE="vertical-align: top"|
{| border="1" class="wikitable"
! width="500" style="background: none repeat scroll 0% 0% rgb(0, 83, 139);" | Configure IP Network for voip0
! width="500" style="background: none repeat scroll 0% 0% rgb(0, 83, 139);" | Configure IP Network for voip1
|-
|
*Modify [[Toolpack:Configuring_Virtual_Port_SBC_B|voip0 virtual port]]:
**'''Name''': voip0
**'''Untagged''': unselect
**'''VLAN id''': 752
*Modify [[Toolpack:Configuring_VoIP_Interfaces_E|voip0 IP Address]]:
**'''Interface Name''': voip0
**'''Service to use''': RTP
**'''Virtual port''': TB002177:voip0
**'''IP address''': 192.168.152.10
**'''Netmask''': 255.255.255.0
|
*Modify [[Toolpack:Configuring_Virtual_Port_SBC_B|voip1 virtual port]]:
**'''Name''': voip1
**'''Untagged''': unselect
**'''VLAN id''': 753
*Modify [[Toolpack:Configuring_VoIP_Interfaces_E|voip1 IP Address]]:
**'''Interface Name''': voip1
**'''Service to use''': RTP
**'''Virtual port''': TB002177:voip1
**'''IP address''': 192.168.153.10
**'''Netmask''': 255.255.255.0
|-
|}
== Sip configuration ==
{| colspan="4" border="1" class="wikitable"
{| colspan="4" border="1" class="wikitable"
! width="250" style="background: none repeat scroll 0% 0% rgb(0, 83, 139);" | Configure SIP
! width="250" style="background: none repeat scroll 0% 0% rgb(0, 83, 139);" | Configure SIP
Line 103: Line 172:
*[[Toolpack:Tsbc_Protocol_Stack_Settings_3.0|Configure SIP]]
*[[Toolpack:Tsbc_Protocol_Stack_Settings_3.0|Configure SIP]]
** For WAN0
** For WAN0
***IP port range parameters:
***RTP port ranges parameters:
****'''Name''': pr_wan0
****'''Name''': pr_wan0
****'''IP Interface''': vlan_1650:wan0
****'''IP Interface''': vlan_1650:wan0
Line 118: Line 187:
****'''SIP Transport Servers''': ts_wan0
****'''SIP Transport Servers''': ts_wan0
** For LAN0
** For LAN0
***IP port range parameters:
***RTP port ranges parameters:
****'''Name''': pr_lan0
****'''Name''': pr_lan0
****'''IP Interface''': vlan_1651:lan0
****'''IP Interface''': vlan_1651:lan0

Latest revision as of 12:16, 3 January 2025


This article applies to: Product Version
SBC 3.1, 3.3


Perequisites

Perequisites
  • ProSBC (or Tsbc) Host
Network device name    Network device role    Network Config
-------------------    -------------------    -------------------
mgmt0                  mgmt                   Untagged
wan0                   LAN/WAN                Tagged 1650
lan0                   LAN/WAN                Tagged 1651
trans0                 LAN/WAN                Tagged 752     
trans1                 LAN/WAN                Tagged 753     
ctrl0                  ctrl0                  Tagged 750
ctrl1                  ctrl1                  Tagged 751

NOTE: The 'Network device names' for transcoding must be trans0 and trans1

  • Hardware Unit - TB002177 is the TSBC-HW-TRANS unit in the below setup
 Network device name    Network device role    Network Config
-------------------    -------------------    -------------------
voip0                   LAN/WAN                Tagged 752
voip1                   LAN/WAN                Tagged 753
eth0                    ctrl0                  Untagged PVID 750  **
eth1                    ctrl1                  Untagged PVID 751  **

NOTE: On the network switch, the control ports on the Hardware unit need to be configure with Link Type: Access

Two subnet, Two IP Addresses, tagged

Network configuration

Configure IP Network for wan0 Configure IP Network for lan0 Configure IP Network for trans0 Configure IP Network for trans1
  • Create wan0 IP Address:
    • Name: wan0
    • Service to use: RTP, SIP
    • Host VLAN: vp_wan0:vlan_1650
    • IP address: 192.168.150.1
    • Netmask: 255.255.255.0
  • Create lan0 IP Address:
    • Name: lan0
    • Service to use: RTP, SIP
    • Host VLAN: vp_lan0:vlan_1651
    • IP address: 192.168.151.1
    • Netmask: 255.255.255.0
  • Create trans0 IP Address:
    • Name: trans0
    • Service to use: RTP
    • Host VLAN: vp_trans0:vlan_752
    • IP address: 192.168.152.1
    • Netmask: 255.255.255.0
  • Create trans1 IP Address:
    • Name: trans1
    • Service to use: RTP
    • Host VLAN: vp_trans1:vlan_753
    • IP address: 192.168.153.1
    • Netmask: 255.255.255.0

Transcoding unit configuration

Add transcoding unit


Transcoding unit network configuration

Configure IP Network for voip0 Configure IP Network for voip1
  • Modify voip0 IP Address:
    • Interface Name: voip0
    • Service to use: RTP
    • Virtual port: TB002177:voip0
    • IP address: 192.168.152.10
    • Netmask: 255.255.255.0
  • Modify voip1 IP Address:
    • Interface Name: voip1
    • Service to use: RTP
    • Virtual port: TB002177:voip1
    • IP address: 192.168.153.10
    • Netmask: 255.255.255.0

Sip configuration

Configure SIP
  • Configure SIP
    • For WAN0
      • RTP port ranges parameters:
        • Name: pr_wan0
        • IP Interface: vlan_1650:wan0
        • RTP Port min: 20000
        • RTP Port max: 40000
      • SIP transport server parameters:
        • Name: ts_wan0
        • Port: 5060
        • IP Interface: vlan_1650:wan0
      • SIP NAP parameters:
        • Name: nap_sip_wan0
        • Proxy Address: 192.168.150.10
        • Port Range: vlan_1650:wan0:pr_wan0:20000-40000
        • SIP Transport Servers: ts_wan0
    • For LAN0
      • RTP port ranges parameters:
        • Name: pr_lan0
        • IP Interface: vlan_1651:lan0
        • RTP Port min: 20000
        • RTP Port max: 40000
      • SIP transport server parameters:
        • Name: ts_lan0
        • Port: 5060
        • IP Interface: vlan_1651:lan0
      • SIP NAP parameters:
        • Name: nap_sip_lan0
        • Proxy Address: 192.168.151.10
        • Port Range: vlan_1651:lan0:pr_lan0:20000-40000
        • SIP Transport Servers: ts_lan0
Retrieved from "https://docs.telcobridges.com/w/index.php?title=Use_Cases:HW_Transcoding_Configuration_UseCase1_A&oldid=34626"