Configuring SIP Registration for regular NAP: Difference between revisions

Latest revision as of 11:26, 26 December 2023

This article applies to:	Product	Version
This article applies to:	SBC	3.0

A regular NAP is a NAP with a specific Proxy address (either IP address or FQDN from 3.1 onward). Configuring SIP Registration for a regular NAP requires no extra steps. A NAP that accepts SIP registration must be a Registrar. A Registrar accepts SIP registration requests from ProSBC after ProSBC receives the request from a remote SIP end point that wants to register on the registrar.

You must configure SIP Registration Domain(s) for your regular NAP and associate them with the regular NAP (Registrar).

To create a new NAP:

1- Click NAPs in the navigation panel

2- Click Create New NAP

3- Create the new NAP:

Enter a name for the NAP
Click Create

4- Verify that the NAP was successfully created message appears

5- Associate a SIP transport server with the new NAP:

Select a SIP Transport Server from the Available list
Click "<<" to associate the LAN_SIP_TS with the NAP

6- Enter SIP Server proxy address:

7- Associate a Port range with the new NAP:

Select a port range from the Available list
Click "<<" to associate LAN_Vlan:0 Port range with the NAP

8- Associate a SIP Domain with the new NAP. If you have more then 1 registrar domain using the same registrar you can associate all of them with the NAP:

Select a sip domain from the Available list
Click "<<" to associate the SIP Domain with the NAP

9- Configure settings for the following parameter groups as required:

Registration Parameters
Authentication Parameters
Network Address Translation
SIP-I Parameters
Advanced Parameters

Click Save

Note: If you are using multiple registrations to the same destination with different ports, you must add the port number in the Address to register too.

@@ Line 1: / Line 1: @@
-=== '''''Applies to version(s): v3.0''''' ===
+{{DISPLAYTITLE:Configuring SIP Registration for regular NAP}}
-{{DISPLAYTITLE:Creating a SIP Domain}}
-A SIP domain represents a grouping of devices (or users) that can communicate with one another.
-You must configure SIP Registration Domain for your system. The first step in doing so is to create a SIP Domain:
+{| class="wikitable"
+|-
+|rowspan="2"|This article applies to:
+|'''Product'''
+|'''Version'''
+|-
+|SBC
+|3.0
+|}
+A regular NAP is a NAP with a specific Proxy address (either IP address or FQDN from 3.1 onward). Configuring SIP Registration for a regular NAP requires no extra steps. A NAP that accepts SIP registration must be a Registrar. A Registrar accepts SIP registration requests from ProSBC after ProSBC receives the request from a remote SIP end point that wants to register on the registrar.
-- Click '''SIP Domain''' in the navigation panel
+You must configure SIP Registration Domain(s) for your regular NAP and associate them with the regular NAP (Registrar).
-[[Image:SIP_Domain_NavigationMenu.png]]
+To create a new NAP:
+- Click '''NAPs''' in the navigation panel
-- Click '''Create New Domain'''
+[[Image:NAP_NavigationMenu.png]]
-[[Image:Create_SIP_Domain.png]]
+- Click '''Create New NAP'''
-- Create the new Domain:
+[[Image:Create_New_NAP_SIP.png]]
-* Enter a configuration '''Name''' for this domain.
-* Enter a '''Domain Name''' for the SIP Registration Domain (domain can be a FQDN or an IP address)
+- Create the new NAP:
-* Set the number '''Maximum Registered Users''' for this domain
-* Set the Expires value used by SBC when the remote device doesn't supply one ('''Default Contact Expire''')
+* Enter a '''name''' for the NAP
-* Select '''Routing Method''' the system will use to route calls to registered users (if enabled in routing scripts).
-** '''Register source''': Sends SIP Invite to the registering source IP address.
-** '''Contact''': Sends SIP Invite to the 'contact' from the Register message.
-* Set the '''Default Contact Expiration''', this value will be used when no ''Expires'' value is supplied by the user agent.
-* Set the '''Minimum Contact Expiration''', this is the minimum ''Expires'' value that can be supplied by a user agent. Lower values will be rejected with a 423 'Interval too brief' response.
-* Set the '''Maximum Contact Expiration''', this is the maximum ''Expires'' value that can be supplied by a user agent. Higher value are replaced by this parameter.
-* Forwarding Parameters:
-** Select the Registration '''Forwarding Mode''' to the registrar:
-*** '''Contact Remapping''': Changes the user and the IP address.
-*** '''Contact Passthrough''': Doesn't change anything. Enables devices to be contacted directly without going through the SBC.
-** Set '''Minimum Registrar Expiration''', this is the minimum ''Expires'' value sent by the SBC to the registrar.  If a user agent 'Expires' value is greater than this parameter, the SBC will do rate adaptation between the user agent and the Registrar.
-** Set '''Maximum Pending Register Forward''', the maximum number of simultaneous pending register requests allowed for this domain.  New REGISTER request are being refused passed this threshold.
-** Set '''Maximum Simultaneous Register Forward''', the  maximum number of simultaneous active register requests allowed for this domain. New REGISTER request are being refused passed this threshold.
-** Select the Registration '''Registrar Selection Mode''' to the registrar:
-*** '''Active/Standby''': The active registrar is the one with status up and the lowest priority (automatic fallback).
-** Enable the '''Forward After Switchover''': After a switchover, the first register refresh request from each user will be forwarded to the active registrar.
 * Click '''Create'''
-[[Image:Create_SIP_Domain1.png]]
+[[Image:SIP_Server_NAP_Create.png]]
+- Verify that the '''NAP was successfully created''' message appears
+[[Image:Create_New_NAP_SIP2.png]]
+- Associate a SIP transport server with the new NAP:
+* Select a '''SIP Transport Server''' from the '''Available''' list
+* Click '''"<<"''' to associate the '''LAN_SIP_TS''' with the NAP
+[[Image:SIP_Server_NAP_Create_1.png]]
+- Enter SIP Server proxy address:
+[[Image:SIP_Server_NAP_Create_2.png]]
+- Associate a Port range with the new NAP:
+* Select a '''port range''' from the '''Available''' list
+* Click '''"<<"''' to associate '''LAN_Vlan:0''' Port range with the NAP
+[[Image:SIP_Server_NAP_Create_3.png]]
+- Associate a SIP Domain with the new NAP. If you have more then 1 registrar domain using the same registrar you can associate all of them with the NAP:
-- Verify that the '''Sip registration domain was successfully created''' message appears
+* Select a '''sip domain''' from the '''Available''' list
+* Click '''"<<"''' to associate the SIP Domain with the NAP
-[[Image:Create_SIP_Domain2.png]]
+[[Image:Open_NAP_Create_3.png]]
-<br><br>
-[[Image:Create_SIP_Domain3.png]]
-- Add the domain to one or multiple NAPs from which users are allowed to register for this domain
-* Click '''NAPs''' in the navigation panel
-* Click on a NAP to bind the SIP Domain to
-* Add the SIP Domain to the NAP (bottom of the page):
-[[Image:bind_domain_to_nap.png]]
+- Configure settings for the following parameter groups as required:
+*Registration Parameters
+*Authentication Parameters
+*Network Address Translation
+*SIP-I Parameters
+*Advanced Parameters
-- Multiple registrars (registration redundancy)
+*Click '''Save'''
-Multiple registrars can be created per domain, for redundancy.
-* Registrars are ordered by priority
-* Users' registration requests are forwarded to the available registrar with the highest priority in the list
-* SIP 'options' polling is used to determine which registrars are available or not
-[[Image:multiple_registrars.png]]
+[[Image:SIP_Server_NAP_Create_4.png]]
+* '''Note:''' If you are using multiple registrations to the same destination with different ports, you must add the port number in the '''Address to register''' too.
-== Create routes for registered users ==
+[[Image:different_port.png]]
-In most cases, TBSC will be required to route SIP calls (SIP Invite) to registered users. That's done by [[Sip_registration_forwarding#SIP_Calls_routing|creating appropriate routes]].