Actions

Toolpack:Creating an M3UA SAP (IPSP) B: Difference between revisions
 
(7 intermediate revisions by the same user not shown)
Line 1: Line 1:
=== '''''Applies to version(s): v2.8''''' ===
=== '''''Applies to version(s): v2.8''''' ===
{{DISPLAYTITLE:Creating an M3UA SAP}}
{{DISPLAYTITLE:Creating an M3UA SAP (IPSP)}}
Once an M3UA configuration is created, you must then create a new M3UA service access point (SAP) for your system. The SAP is an identifying label for endpoints in your network.
Once an M3UA configuration is created, you must then create a new M3UA service access point (SAP) for your system. The SAP is an identifying label for endpoints in your network.


Line 18: Line 18:


* Enter a '''name''' for the SAP
* Enter a '''name''' for the SAP
* Select an '''SCTP adapter''' to use
* Select an '''Unit''' to use
* Select an '''SCTP source port'''
* Select an '''SCTP source port'''
* Click '''Create'''
* Click '''Create'''
Line 27: Line 27:
4- Verify that the '''"M3ua Sap was successfully created"''' message appears
4- Verify that the '''"M3ua Sap was successfully created"''' message appears


[[Image:Toolpack_v2.5_M3UA_SAP_Created.png]]
[[Image:Create_M3UA_SAP_2.png]]




Line 35: Line 35:
* Click the'''"<<"''' button to associate the interface with the SAP
* Click the'''"<<"''' button to associate the interface with the SAP


[[Image:Create_M3UA_SAP_2.png]]
[[Image:Create_M3UA_SAP_3.png]]


==List of Parameters==
==List of Parameters==
Line 42: Line 42:
* [[Parameter: SCTP Adapter|SCTP Adapter]]
* [[Parameter: SCTP Adapter|SCTP Adapter]]
* [[Parameter: SCTP Source Port|SCTP Source Port]]
* [[Parameter: SCTP Source Port|SCTP Source Port]]
'''M3UA SAP Timers'''
* [[Parameter: SCTP Primitive Timer|SCTP Primitive Timer]]
* [[Parameter: SCTP Association Timer|SCTP Association Timer]]
<div class="mw-collapsible mw-collapsed" data-collapsetext="SCTP SAP Advanced Parameters" data-expandtext="SCTP SAP Advanced Parameters" style="width: 400px;">
{| class="wikitable"
|-
* [[Parameter: Maximum data size|Maximum data size]]
* [[Parameter: Maximum ACK delay|Maximum ACK delay]]
* [[Parameter: Maximum datagram before ACK|Maximum datagram before ACK]]
* [[Parameter: Initial Retransmission Timeout (RTO)|Initial Retransmission Timeout (RTO)]]
* [[Parameter: Minimum Retransmission Timeout (RTO)|Minimum Retransmission Timeout (RTO)]]
* [[Parameter: Maximum Retransmission Timeout (RTO)|Maximum Retransmission Timeout (RTO)]]
* [[Parameter: Freeze timer|Freeze timer]]
* [[Parameter: Bundle timer|Bundle timer]]
* [[Parameter: Cookie life time|Cookie life time]]
* [[Parameter: Delay between heartbeat|Delay between heartbeat]]
* [[Parameter: Maximum datagram burst|Maximum datagram burst]]
* [[Parameter: Maximum heartbeat at each RTO|Maximum heartbeat at each RTO]]
* [[Parameter: Shutdown Guard Timer|Shutdown Guard Timer]]
* [[Parameter: Handle INIT datagram|Handle INIT datagram]]
* [[Parameter: Abort negociation if nb. streams mismatch|Abort negociation if nb. streams mismatch]]
* [[Parameter: Flow-control up threshold|Flow-control up threshold]]
* [[Parameter: Flow-control down threshold|Flow-control down threshold]]
|}
</div>

Latest revision as of 13:30, 28 September 2015

Applies to version(s): v2.8

Once an M3UA configuration is created, you must then create a new M3UA service access point (SAP) for your system. The SAP is an identifying label for endpoints in your network.

To create an M3UA SAP:

1- Click M3UA in the navigation panel:


2- Click Create New M3ua Sap in the M3UA configuration panel


3- Configure the new SAP:

  • Enter a name for the SAP
  • Select an Unit to use
  • Select an SCTP source port
  • Click Create


4- Verify that the "M3ua Sap was successfully created" message appears


5- Associate an IP interface with the new SAP:

  • Select an available IP interface
  • Click the"<<" button to associate the interface with the SAP

List of Parameters

M3UA SAP Timers


Retrieved from "https://docs.telcobridges.com/w/index.php?title=Toolpack:Creating_an_M3UA_SAP_(IPSP)_B&oldid=19299"