View source for ProSBC:SIP Network Peering / IP Carrier Interconnection:Configuration A

{{DISPLAYTITLE:ProSBC:SIP Network Peering / IP Carrier Interconnection:Example}}

=== '''''Applies to version: v3.0 v3.1''''' ===

=Introduction=
The SIP Network Peering / IP Carrier Interconnection Example Configuration provides you with a step by step SIP Network Peering / IP Carrier Interconnection Configuration of [[ProSBC|ProSBC]] systems, using the Web Portal configuration tool. Complete general installation configuration steps, before you begin configuring your specific scenario.

=SIP Network Peering / IP Carrier Interconnection Example=

[[Image:ProSBC_SIP_Peering.png]]<br>

==Prerequisites==
[[ProSBC|ProSBC]] devices must be installed as described in their respective [[Product_Installation_SBC|installation guides]].

=IP Network Configuration= 
 
==Virtual Port Configuration for Wide Area Network==
1. Select '''IP Interfaces''' from the navigation panel

[[Image:Create Voip Interface_Tsbc_0.png]] <br><br>
<br><br>

2. Click the '''Virtual Ports''' tab. 
*Click '''Create New Virtual Port''' 

[[Image:SIP_Trunking_VP_Create.png]]<br><br> 

3. Configure the virtual port.

*Enter a name for the virtual port
*Select the host(s) to which the virtual port is assigned
*Select a physical port to which the virtual port is assigned

*Click '''Create'''

[[Image:SIP_Trunking_VP_WAN.png]]<br><br>

4. Create a VLAN that uses this virtual port
*Click '''Create new Host VLAN'''

[[Image:SIP_Trunking_Vlan_WAN.png]]<br><br>

5. Configure the new VLAN

*Enter a name for the VLAN
*If the port is to be used untagged, make sure '''Untagged''' is checked. 
*If the port is to be used with a 802.1Q tag, uncheck '''Untagged''' and enter a VLAN ID. 
*Click '''Create'''

[[Image:SIP_Trunking_Vlan_WAN_Interface_1.png]] <br><br>

OR

[[Image:SIP_Trunking_Vlan_WAN_Interface_2.png]] <br><br>

==Virtual Port Configuration for Local Area Network==
1. Select '''IP Interfaces''' from the navigation panel

[[Image:Create Voip Interface_Tsbc_0.png]] <br><br>
<br><br>

2. 2. Click the '''Virtual Ports''' tab. 
*Click '''Create New Virtual Port'''

[[Image:SIP_Trunking_VP_Create_LAN.png]]<br><br> 

3. Configure the virtual port.

*Enter a name for the virtual port
*Select the host(s) to which the virtual port is assigned
*Select a physical port to which the virtual port is assigned

*Click '''Create'''

[[Image:SIP_Trunking_VP_LAN.png]]<br><br>

4. Create a VLAN that uses this virtual port
*Click '''Create new Host VLAN'''

[[Image:SIP_Trunking_Vlan_LAN.png]]<br><br>

5. Configure the new VLAN

*Enter a name for the VLAN
*If the port is to be used untagged, make sure '''Untagged''' is checked. 
*If the port is to be used with a 802.1Q tag, uncheck '''Untagged''' and enter a VLAN ID. 
*Click '''Create'''

[[Image:SIP_Trunking_Vlan_LAN_Interface_1.png]] <br><br>

OR

[[Image:SIP_Trunking_Vlan_LAN_Interface_2.png]] <br><br>

==Configuring IP Interface for Wide Area Network==

1. Select '''IP Interfaces''' from the navigation panel: 

[[Image:Create_IP_Interface_Tsbc_0.png]]<br><br>
<br><br>

2. Click the '''IP Interfaces''' tab.
*Click '''Create New IP Interface'''

[[Image:Create_IP_if_WAN_1.png]]<br><br>
<br><br>

3. Configure the IP interface: 

*Enter a name for the interface
*Select 1 or more services to use for the IP interface (RTP and SIP).
*Select the '''Host VLAN''' from which IP packets will exit.
*Indicate whether or not to use DHCP to automatically get an IP address for this port. (selecting this option removes the need to enter and IP address, Netmask, and Gateway)
*Enter an '''IP address''' 
*Enter a '''Netmask''' 
*Enter a '''gateway address''' 
*Click '''Save'''


[[Image:Create_IPif_WAN_1.png]]<br><br>
<br><br>

==Configuring IP Interface for Local Area Network==

1. Select '''IP Interfaces''' from the navigation panel: 

[[Image:Create_IP_Interface_Tsbc_0.png]]<br><br>

2. Click the '''IP Interfaces''' tab.
*Click '''Create New IP Interface'''

[[Image:Create_IPif_LAN.png]]<br><br>

3. Configure the IP interface: 

*Enter a name for the interface
*Select 1 or more services to use for the IP interface (RTP and SIP).
*Select the '''Host VLAN''' from which IP packets will exit.
*Indicate whether or not to use DHCP to automatically get an IP address for this port. (selecting this option removes the need to enter and IP address, Netmask, and Gateway)
*Enter an '''IP address''' 
*Enter a '''Netmask''' 
*Enter a '''gateway address''' 
*Click '''Save'''

[[Image:Create_IP_if_LAN_1.png]]<br><br>

=SIP Stack Configuration= 

You must configure SIP signaling for your system. The first step in doing so is to create a SIP stack:

1- Click '''SIP''' in the navigation panel

[[Image:SIP_NavigationMenu.png]]


2- Click '''Create New Sip'''

[[Image:Create_New_SIP.png]]

3- Create the new SIP stack:

* Verify that the box labeled '''Enabled''' is checked
* Enter a '''name''' for the stack
* Click '''Create'''

[[Image:SIP_Trunking_SIP_Stack.png]]

==SIP Transport Server Configuration for Wide Area Network==

1- Click '''SIP''' in the navigation panel

[[Image:SIP_NavigationMenu.png]]


2- Select a SIP stack for which you wish to create a transport server

[[Image:SIP_Config_List.png]]

3- Click '''Create New Transport Server'''

[[Image:WAN_SIP_TransportServer.png]]


4- Create the new SIP transport server:

* Enter a '''name''' for the server
* Select an appropriate '''port type'''
* Select an appropriate host '''IP interface'''
* Click '''Create'''

[[Image:WAN_SIP_TransportServer1.png]]

==SIP Transport Server Configuration for Local Area Network==

1- Click '''SIP''' in the navigation panel

[[Image:SIP_NavigationMenu.png]]


2- Select a SIP stack for which you wish to create a transport server

[[Image:SIP_Config_List.png]]

3- Click '''Create New Transport Server'''

[[Image:WAN_SIP_TransportServer.png]]


4- Create the new SIP transport server:

* Enter a '''name''' for the server
* Select an appropriate '''port type'''
* Select an appropriate host '''IP interface'''
* Click '''Create'''

[[Image:LAN_SIP_TransportServer1.png]]

=SIP NAP=

A Network Access Point or NAP represents the entry point to another network or destination peer (e.g. SIP proxy,SIP trunk, etc)

==SIP NAP Configuration for Wide Area Network==

To create a new NAP:

1- Click '''NAPs''' in the navigation panel

[[Image:NAP_NavigationMenu.png]]


2- Click '''Create New NAP'''

[[Image:Create_New_NAP_SIP.png]]


3- Create the new NAP:

* Enter a '''name''' for the NAP
* Click '''Create'''

[[Image:SIP_Trunk_NAP_Create.png]]


4- Verify that the '''NAP was successfully created''' message appears

[[Image:Create_New_NAP_SIP2.png]]

5- Associate a SIP transport server with the new NAP:

* Select a '''SIP Transport Server''' from the '''Available''' list
* Click '''"<<"''' to associate the '''WAN_SIP_TS''' with the NAP

[[Image:SIP_Trunk_NAP_Create_1.png]]

6- Enter SIP Trunk proxy address:

[[Image:SIP_Trunk_NAP_Create_2.png]]

7- Associate a Port range with the new NAP:

* Select a '''port range''' from the '''Available''' list
* Click '''"<<"''' to associate '''WAN_Vlan:0''' Port range with the NAP

[[Image:SIP_Trunk_NAP_Create_3.png]]

8- Configure settings for the following parameter groups as required:
*Registration Parameters
*Authentication Parameters
*Network Address Translation
*SIP-I Parameters
*Advanced Parameters

*Click '''Save''' 

[[Image:SIP_Trunk_NAP_Create_4.png]]

==SIP NAP Configuration for Local Area Network==

To create a new NAP:

1- Click '''NAPs''' in the navigation panel

[[Image:NAP_NavigationMenu.png]]


2- Click '''Create New NAP'''

[[Image:Create_New_NAP_SIP.png]]


3- Create the new NAP:

* Enter a '''name''' for the NAP
* Click '''Create'''

[[Image:SIP_Server_NAP_Create.png]]


4- Verify that the '''NAP was successfully created''' message appears

[[Image:Create_New_NAP_SIP2.png]]

5- Associate a SIP transport server with the new NAP:

* Select a '''SIP Transport Server''' from the '''Available''' list
* Click '''"<<"''' to associate the '''LAN_SIP_TS''' with the NAP

[[Image:SIP_Server_NAP_Create_1.png]]

6- Enter SIP Server proxy address:

[[Image:SIP_Server_NAP_Create_2.png]]

7- Associate a Port range with the new NAP:

* Select a '''port range''' from the '''Available''' list
* Click '''"<<"''' to associate '''LAN_Vlan:0''' Port range with the NAP

[[Image:SIP_Server_NAP_Create_3.png]]

8- Configure settings for the following parameter groups as required:
*Registration Parameters
*Authentication Parameters
*Network Address Translation
*SIP-I Parameters
*Advanced Parameters

*Click '''Save''' 

[[Image:SIP_Server_NAP_Create_4.png]]

==Access Control List==

ProSBC will automatically create Access Control List for each NAP you created.

[[Image:SIP_Access_Control_List_1.png]]


If you double click one of the created ACL, you will see ProSBC only accept the calls if the source IP matches. In this sample; the calls from 192.168.1.10 will accepted only.


[[Image:SIP_Access_Control_List_2.png]]

=Call Route=

You must set up call routing for your system. [[Call routing]] refers to the ability to route calls based on criteria such as origin, destination, time of day, service provider rates, and more.



==Route Configuration for SIP Trunk to SIP Server==

1- Click '''Routes''' in the navigation panel

[[Image:CreateCallRoute_0.png]]


2- Click '''Create New Static Route'''

[[Image:CreateCallRoute_1.png]]


3- Create the new route:

* Enter a '''RoutesetName''' for the route
* Select  '''SIP_TRUNK_NAP''', to match calls from Trunk NAP 
* Select '''SIP_SERVER_NAP'''
* Click '''Create'''

[[Image:Route_Trunk_to_Server.png]]


4- Verify that the '''"Route was successfully created"''' message appears, and that the new route is listed in the Routeset list

[[Image:Route_Trunk_to_Server_1.png]]

==Route Configuration for SIP Server to SIP Trunk==

1- Click '''Routes''' in the navigation panel

[[Image:CreateCallRoute_0.png]]


2- Click '''Create New Static Route'''

[[Image:CreateCallRoute_1.png]]


3- Create the new route:

* Enter a '''RoutesetName''' for the route
* Select  '''SIP_SERVER_NAP''', to match calls from Trunk NAP 
* Select '''SIP_TRUNK_NAP'''
* Click '''Create'''

[[Image:Route_Server_to_Trunk.png]]


4- Verify that the '''"Route was successfully created"''' message appears and that the new route is listed in the Routeset list

[[Image:Route_Server_to_Trunk_1.png]]

=Activating the Configuration=

Changes made to the configuration of the ProSBC units are stored in the OAM&P Configuration and Logging database. In order for changes to be used by the system, they must first be activated. This is done at the system level and accessed from the Navigation panel.

Check the following link for activating the configuration;

[[Toolpack:Activating_the_Configuration_D]]

=SBC Use Cases=
[[Toolpack:Tsbc Use Cases A|SBC Use Cases]]

=SBC Turorial Guide V3.0=
[[Tmedia Tsig Tdev Tutorial Guide v3.0|Version 3.0]]


[[Category:Revise on Major]]