Toolpack:Verifying that an Application is Operating A - Revision history

Allyntree at 18:08, 9 July 2012

2012-07-09T18:08:14Z

← Older revision		Revision as of 14:08, 9 July 2012
Line 1:		Line 1:
	=== '''''Applies to version(s): v2.5, v2.6.''''' ===		=== '''''Applies to version(s): v2.5, v2.6.''''' ===
	{{DISPLAYTITLE:~~Toolpack: Navigating the Web Portal~~}}		{{DISPLAYTITLE:Verifying that an Application is Operating}}
	When an application’s target state is set to run, there are a number of crucial verifications that you should conduct in order to know that an application is running properly. These verifications are as follows:		When an application’s target state is set to run, there are a number of crucial verifications that you should conduct in order to know that an application is running properly. These verifications are as follows:

Allyntree: moved Toolpack:Verifying that an Application is Operating to Toolpack:Verifying that an Application is Operating A: New naming convention

2012-06-04T19:56:29Z

moved Toolpack:Verifying that an Application is Operating to Toolpack:Verifying that an Application is Operating A: New naming convention

← Older revision	Revision as of 15:56, 4 June 2012
(No difference)

Allyntree at 19:56, 4 June 2012

2012-06-04T19:56:00Z

← Older revision		Revision as of 15:56, 4 June 2012
Line 1:		Line 1:
			=== '''''Applies to version(s): v2.5, v2.6.''''' ===
			{{DISPLAYTITLE:Toolpack: Navigating the Web Portal}}
	When an application’s target state is set to run, there are a number of crucial verifications that you should conduct in order to know that an application is running properly. These verifications are as follows:		When an application’s target state is set to run, there are a number of crucial verifications that you should conduct in order to know that an application is running properly. These verifications are as follows:

Ktrueman: clean up

2009-07-10T15:30:22Z

clean up

← Older revision		Revision as of 11:30, 10 July 2009
Line 1:		Line 1:
	When an application’s target state is set to run, there are a number of crucial verifications that you should conduct in order to know that an application is running properly. These verifications are as follows:		When an application’s target state is set to run, there are a number of crucial verifications that you should conduct in order to know that an application is running properly. These verifications are as follows:

	*Verify the application’s current path. It is important that once the application has been set to run, a path is displayed.		*'''Verify the application’s current path.''' It is important that once the application has been set to run, a path is displayed.

	*Verify the TDM interface. If you are running a TDM application on your Tmedia unit then you can verify the TDM interface. Although, you most likely have not yet configured the TDM interface of the Tmedia unit, certain status LEDS will indicate that your application is operational.		*'''Verify the TDM interface.''' If you are running a TDM application on your Tmedia unit then you can verify the TDM interface. Although, you most likely have not yet configured the TDM interface of the Tmedia unit, certain status LEDS will indicate that your application is operational.

	*Verify the IP Interfaces. Your Tmedia unit is furnished with two IP interfaces for access to a VoIP network. Although you have not as of yet configured the interfaces, certain LED indications will be displayed. See figure below.		*'''Verify the IP Interfaces.''' Your Tmedia unit is furnished with two IP interfaces for access to a VoIP network. Although you have not as of yet configured the interfaces, certain LED indications will be displayed. See figure below.


	[[Image:Schematic-device-rear-ports.jpg\|400px]]		[[Image:Schematic-device-rear-ports.jpg\|400px]]

Ktrueman: initial content

2009-07-09T20:31:57Z

initial content

New page

When an application’s target state is set to run, there are a number of crucial verifications that you should conduct in order to know that an application is running properly. These verifications are as follows:

*Verify the application’s current path. It is important that once the application has been set to run, a path is displayed.

*Verify the TDM interface. If you are running a TDM application on your Tmedia unit then you can verify the TDM interface. Although, you most likely have not yet configured the TDM interface of the Tmedia unit, certain status LEDS will indicate that your application is operational.

*Verify the IP Interfaces. Your Tmedia unit is furnished with two IP interfaces for access to a VoIP network. Although you have not as of yet configured the interfaces, certain LED indications will be displayed. See figure below.

[[Image:Schematic-device-rear-ports.jpg|400px]]