Toolpack:Starting Continuity Check ISUP A - Revision history

Allyntree at 18:12, 24 June 2024

2024-06-24T18:12:13Z

← Older revision		Revision as of 14:12, 24 June 2024
Line 7:		Line 7:
	\|-		\|-
	\|Tmedia		\|Tmedia
	\|2.7, ~~2.8, 2~~.9, 2~~.10~~, 3.0, 3.2		\|3.0, 3.2, 3.3
	\|}		\|}

Allyntree at 19:16, 1 December 2020

2020-12-01T19:16:05Z

← Older revision		Revision as of 15:16, 1 December 2020
Line 1:		Line 1:
	~~=== '''''Applies to version(s): 2.7, 2.8, 2.9, 3.0, 3.2''''' ===~~
	{{DISPLAYTITLE:Starting Manual Continuity Check}}		{{DISPLAYTITLE:Starting Manual Continuity Check}}
			{\| class="wikitable"
			\|-
			\|rowspan="3"\|This article applies to:
			\|'''Product'''
			\|'''Version'''
			\|-
			\|Tmedia
			\|2.7, 2.8, 2.9, 2.10, 3.0, 3.2
			\|}

	Note: the option might not be available if the resources required for the test (tone generation and detection) are not available.		Note: the option might not be available if the resources required for the test (tone generation and detection) are not available.

Allyntree at 18:00, 21 August 2020

2020-08-21T18:00:09Z

← Older revision		Revision as of 14:00, 21 August 2020
Line 7:		Line 7:
	1- Select '''SS7->ISUP''' from the navigation panel		1- Select '''SS7->ISUP''' from the navigation panel

	2- Click on the '''Status''' tab and click on the appropriate ISUP Stack		2- Click the '''Status''' tab and click on the appropriate ISUP Stack

	3- Click on the '''Interfaces''' tab and select the appropriate ISUP Interface		3- Click the '''Interfaces''' tab and select the appropriate ISUP Interface

	4- Click on the '''Circuit Groups''' tab and select the appropriate Circuit Group		4- Click the '''Circuit Groups''' tab and select the appropriate Circuit Group


	'''If you want to start a continuity check on all circuits of a circuit group:'''		'''If you want to start a continuity check on all circuits of a circuit group:'''
	*Select '''Yes''' for'''Start continuity check''' and click on '''Apply states'''		*Select '''Yes''' for'''Start continuity check''' and click on '''Apply states'''
	*Click on '''Now''' to refresh the status and see the result of the test. Some of the following stats should be modified:		*Click '''Now''' to refresh the status and see the result of the test. Some of the following stats should be modified:
	**Total ccr success cnt		**Total ccr success cnt
	**Total ccr fail cnt		**Total ccr fail cnt

Allyntree at 17:59, 21 August 2020

2020-08-21T17:59:40Z

← Older revision		Revision as of 13:59, 21 August 2020
Line 1:		Line 1:
	=== '''''Applies to version(s): v2.7.''''' ===		=== '''''Applies to version(s): 2.7, 2.8, 2.9, 3.0, 3.2''''' ===
	{{DISPLAYTITLE:Starting Manual Continuity Check}}		{{DISPLAYTITLE:Starting Manual Continuity Check}}

Nicole Tan: Removed v2.6 from "/* Applies to version(s): v2.6, v2.7. */ "

2013-07-09T19:43:10Z

Removed v2.6 from "Applies to version(s): v2.6, v2.7.: "

← Older revision		Revision as of 15:43, 9 July 2013
Line 1:		Line 1:
	=== '''''Applies to version(s): ~~v2.6,~~ v2.7.''''' ===		=== '''''Applies to version(s): v2.7.''''' ===
	{{DISPLAYTITLE:Starting Manual Continuity Check}}		{{DISPLAYTITLE:Starting Manual Continuity Check}}

Manon Bélanger: first version of the page for manual continuity check (CCR)

2012-12-14T15:17:05Z

first version of the page for manual continuity check (CCR)

New page

=== '''''Applies to version(s): v2.6, v2.7.''''' ===
{{DISPLAYTITLE:Starting Manual Continuity Check}}

Note: the option might not be available if the resources required for the test (tone generation and detection) are not available.

1- Select '''SS7->ISUP''' from the navigation panel

2- Click on the '''Status''' tab and click on the appropriate ISUP Stack

3- Click on the '''Interfaces''' tab and select the appropriate ISUP Interface

4- Click on the '''Circuit Groups''' tab and select the appropriate Circuit Group

'''If you want to start a continuity check on all circuits of a circuit group:'''
*Select '''Yes''' for'''Start continuity check''' and click on '''Apply states'''
*Click on '''Now''' to refresh the status and see the result of the test. Some of the following stats should be modified:
**Total ccr success cnt
**Total ccr fail cnt
**Last ccr unknown cnt
**Last ccr in progress cnt
**Last ccr success cnt
**Last ccr fail cnt
**Last ccr error cnt

'''If you want to start a continuity check on a specific circuit:'''
*Click on the '''Circuits''' tab and select the circuit in the '''Cic''' column.
*Select '''Yes''' for'''Start continuity check''' and click on '''Apply states'''
*Click on '''Now''' to refresh the status and see the result of the test. Some of the following stats should be modified:
**Nb outgoing ccr success
**Nb outgoing ccr fail
**Last ccr result