Toolpack:Reset NetworkDevice A - Revision history

Allyntree at 14:12, 15 June 2024

2024-06-15T14:12:23Z

← Older revision		Revision as of 10:12, 15 June 2024
Line 7:		Line 7:
	\|-		\|-
	\|SBC		\|SBC
	\|3.0, 3.1		\|3.1, 3.3
	\|}		\|}

Allyntree at 19:45, 10 December 2020

2020-12-10T19:45:54Z

← Older revision		Revision as of 15:45, 10 December 2020
Line 1:		Line 1:
	~~=== '''''Applies to version(s) v3.0, v3.1''''' ===~~
	{{DISPLAYTITLE:Resetting the Network Device Role}}		{{DISPLAYTITLE:Resetting the Network Device Role}}
			{\| class="wikitable"
			\|-
			\|rowspan="3"\|This article applies to:
			\|'''Product'''
			\|'''Version'''
			\|-
			\|SBC
			\|3.0, 3.1
			\|}

	Once the FreeSBC/ProSBC is configured, it is possible add or change physical IP interfaces.		Once the FreeSBC/ProSBC is configured, it is possible add or change physical IP interfaces.

Luc Morissette at 16:58, 31 July 2019

2019-07-31T16:58:04Z

← Older revision		Revision as of 12:58, 31 July 2019
Line 26:		Line 26:
	* Click '''Apply Action'''		* Click '''Apply Action'''
	[[Image:Host_action_snapshot_network.png]]		[[Image:Host_action_snapshot_network.png]]


	After a few seconds, refresh the web interface and you will be brought back to the selection of network interfaces: [[TSBC-SW:WebPortal:Initial_Configuration\|Initial Configuration]], Step 8		After a few seconds, refresh the web interface and you will be brought back to the selection of network interfaces: [[TSBC-SW:WebPortal:Initial_Configuration\|Initial Configuration]], Step 8

Luc Morissette at 16:57, 31 July 2019

2019-07-31T16:57:29Z

← Older revision		Revision as of 12:57, 31 July 2019
Line 3:		Line 3:

	Once the FreeSBC/ProSBC is configured, it is possible add or change physical IP interfaces.		Once the FreeSBC/ProSBC is configured, it is possible add or change physical IP interfaces.
	To do so you must reset the network device role settings of the unit.		To do so you must reset the network device role settings of the unit. <br>
	'''Note: this will reallocate the main network controller and stop the service for a few minutes'''		'''Note: this will reallocate the main network controller and stop the service for a few minutes'''

Luc Morissette: Added Change Network Devices Roles

2019-07-31T16:57:07Z

Added Change Network Devices Roles

New page

=== '''''Applies to version(s) v3.0, v3.1''''' ===
{{DISPLAYTITLE:Resetting the Network Device Role}}

Once the FreeSBC/ProSBC is configured, it is possible add or change physical IP interfaces.
To do so you must reset the network device role settings of the unit.
'''Note: this will reallocate the main network controller and stop the service for a few minutes'''

'''To reset the network device role, do the following:'''

1- Click '''Hosts''' in the navigation panel.

[[Image:HostRoleReset_0_A.png]]

2- Select the serial number of the unit.

[[Image:HostRoleReset_1_A.png]]

3- Click the '''Status''' tab.

[[Image:HostRoleReset_2_A.png]]

4- In the Action drop down box select '''Change Network Devices Roles'''
* Click '''Apply Action'''
[[Image:Host_action_snapshot_network.png]]
After a few seconds, refresh the web interface and you will be brought back to the selection of network interfaces: [[TSBC-SW:WebPortal:Initial_Configuration|Initial Configuration]], Step 8