Toolpack:M3UA Use Case A:Configure IP Interface A - Revision history

Allyntree: /* Applies to version(s): v3.0 */

2019-09-06T13:30:52Z

Applies to version(s): v3.0

← Older revision		Revision as of 09:30, 6 September 2019
Line 2:		Line 2:
	{{DISPLAYTITLE:Configuring VoIP Interfaces}}		{{DISPLAYTITLE:Configuring VoIP Interfaces}}

	~~The~~ IP interface of the VoIP0 and VoIP1 ports ~~can be~~ configured by setting the following:		In this use case the IP interface of the VoIP0 and VoIP1 ports are configured by setting the following:

	*IP Address		*IP Address: 192.168.0.55
	*Netmask		*Netmask: 255.255.255.0
	*Gateway		*Gateway: 192.168.0.1

	<br>		<br>

Allyntree: /* To configure a VoIP0 or VoIP1 port */

2019-08-21T16:07:52Z

To configure a VoIP0 or VoIP1 port

← Older revision		Revision as of 12:07, 21 August 2019
Line 40:		Line 40:
	4. The changes are displayed in the IP interfaces information panel:		4. The changes are displayed in the IP interfaces information panel:

	[[Image:Create Voip Interface_3_1.png]]		[[Image:Create Voip Interface_3_1.png]]


	~~<br>~~


	== List of Parameters ==		== List of Parameters ==

Allyntree at 16:02, 21 August 2019

2019-08-21T16:02:24Z

← Older revision		Revision as of 12:02, 21 August 2019
Line 19:		Line 19:
	*Click '''Create New IP Interface'''		*Click '''Create New IP Interface'''

	[[Image:~~Voip_Interface_1a~~.png]]		[[Image:Voip_Interface_1a_1.png]]

	<br> 3. Configure the IP port:		<br> 3. Configure the IP port:
Line 34:		Line 34:
	'''Note:''' The IP addresses of ETH0, ETH1, VOIP0 and VOIP1 must be on different subnets. <br>		'''Note:''' The IP addresses of ETH0, ETH1, VOIP0 and VOIP1 must be on different subnets. <br>

	[[Image:Create Voip ~~Interface_2~~.png]]		[[Image:Create Voip Interface_2_1.png]]

	<br>		<br>
Line 40:		Line 40:
	4. The changes are displayed in the IP interfaces information panel:		4. The changes are displayed in the IP interfaces information panel:

	[[Image:Create Voip ~~Interface_3~~.png]]		[[Image:Create Voip Interface_3_1.png]]


	<br>		<br>

	~~5. Activate the configuration~~

	~~Systems -> Edit -> Activate~~



	~~6. It is necessary to reboot the adapters if you are using the vlan from 3441 to 3450 only.~~

	~~Status -> Adapters -> Click on the adapter Serial Number -> Reboot adapter~~

	~~It will take about 1.5 minutes to restart the unit.~~

	~~'''Note:''' in a 1+1 system, both units must be restarted.~~

Allyntree at 19:09, 8 August 2019

2019-08-08T19:09:12Z

← Older revision		Revision as of 15:09, 8 August 2019
Line 24:		Line 24:

	*Enter a name for the interface		*Enter a name for the interface
	*Select one or more services to use for the IP ~~inteface~~		*Select one or more services to use for the IP interface
	*Select a '''Virtual port''' from which IP packets will exit.		*Select a '''Virtual port''' from which IP packets will exit.
	*Indicate whether or not to use dynamic IP will be used on this interface. For example DHCP to automatically get an IP address for this port. (selecting this option removes the need to enter and IP address, Netmask, and Gateway)		*Indicate whether or not to use dynamic IP will be used on this interface. For example DHCP to automatically get an IP address for this port. (selecting this option removes the need to enter and IP address, Netmask, and Gateway)

Allyntree: Created page with "=== '''''Applies to version(s): v3.0''''' === {{DISPLAYTITLE:Configuring VoIP Interfaces}} The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the foll..."

2019-08-08T19:08:45Z

Created page with "=== '''''Applies to version(s): v3.0''''' === {{DISPLAYTITLE:Configuring VoIP Interfaces}} The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the foll..."

New page

=== '''''Applies to version(s): v3.0''''' ===
{{DISPLAYTITLE:Configuring VoIP Interfaces}}

The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following:

*IP Address
*Netmask
*Gateway

 

== To configure a VoIP0 or VoIP1 port ==

1. Select '''IP Interfaces''' from the navigation panel:

[[Image:Create Voip Interface_0.png]]

 2. Click the '''IP Interfaces''' tab.
*Click '''Create New IP Interface'''

[[Image:Voip_Interface_1a.png]]

 3. Configure the IP port:

*Enter a name for the interface
*Select one or more services to use for the IP inteface
*Select a '''Virtual port''' from which IP packets will exit.
*Indicate whether or not to use dynamic IP will be used on this interface. For example DHCP to automatically get an IP address for this port. (selecting this option removes the need to enter and IP address, Netmask, and Gateway)
*Enter an '''IP address'''
*Enter a '''Netmask'''
*Enter a '''gateway address'''
*Click '''Save'''

'''Note:''' The IP addresses of ETH0, ETH1, VOIP0 and VOIP1 must be on different subnets. 

[[Image:Create Voip Interface_2.png]]

 

4. The changes are displayed in the IP interfaces information panel:

[[Image:Create Voip Interface_3.png]]

 

5. Activate the configuration

Systems -> Edit -> Activate

6. It is necessary to reboot the adapters if you are using the vlan from 3441 to 3450 only.

Status -> Adapters -> Click on the adapter Serial Number -> Reboot adapter

It will take about 1.5 minutes to restart the unit.

'''Note:''' in a 1+1 system, both units must be restarted.

== List of Parameters ==

*[[Parameter: Interface name|Interface name]]
*[[Parameter: Services to use|Services to use]]
*[[Parameter: Virtual port|Virtual port]]
*[[Parameter: Use DHCP|Use dynamic IP]]
*[[Parameter: IP Address|IP Address]]
*[[Parameter: Netmask|Netmask]]
*[[Parameter: Gateway|Gateway]]