Toolpack:Creating the M2PA Configuration B - Revision history

Allyntree at 16:57, 18 September 2014

2014-09-18T16:57:08Z

← Older revision		Revision as of 12:57, 18 September 2014
Line 15:		Line 15:
	* Click '''Create'''		* Click '''Create'''

	[[Image:~~CreateM2pa_1~~.png]]		[[Image:CreateM2pa_1_a.png]]

	3- Verify that the '''"M2ua Cfg was successfully created"''' message appears		3- Verify that the '''"M2ua Cfg was successfully created"''' message appears

Allyntree: /* List of Parameter */

2014-09-18T14:46:14Z

List of Parameter

← Older revision		Revision as of 10:46, 18 September 2014
Line 24:		Line 24:

	* [[Parameter: Name\|Name]]		* [[Parameter: Name\|Name]]
	* [[Parameter: Service Type\|Service Type]]

Allyntree: /* Applies to version(s): v2.7. */

2014-09-18T14:45:57Z

Applies to version(s): v2.7.

← Older revision		Revision as of 10:45, 18 September 2014
Line 17:		Line 17:
	[[Image:CreateM2pa_1.png]]		[[Image:CreateM2pa_1.png]]

	3- Verify that the '''"~~Sctp~~ Cfg was successfully created"''' message appears		3- Verify that the '''"M2ua Cfg was successfully created"''' message appears

	[[Image:CreateM2pa_2.png]]		[[Image:CreateM2pa_2.png]]

Allyntree: /* Applies to version(s): v2.7. */

2014-09-18T14:45:37Z

Applies to version(s): v2.7.

← Older revision		Revision as of 10:45, 18 September 2014
Line 9:		Line 9:
	[[Image:M2pa_0.png]]		[[Image:M2pa_0.png]]

	2- Configure the ~~SCTP~~ service		2- Configure the M2PA service

	* Make sure the box labelled '''Enabled''' is '''checked'''		* Make sure the box labelled '''Enabled''' is '''checked'''

Allyntree: /* Applies to version(s): v2.7. */

2014-09-18T14:45:23Z

Applies to version(s): v2.7.

← Older revision		Revision as of 10:45, 18 September 2014
Line 3:		Line 3:


	To ~~edit your system's~~ M2PA configuration:		To create an M2PA configuration:

	1- Select '''M2PA''' from the navigation panel		1- Select '''M2PA''' from the navigation panel
Line 20:		Line 20:

	[[Image:CreateM2pa_2.png]]		[[Image:CreateM2pa_2.png]]


	==List of Parameter==		==List of Parameter==

Allyntree: This was a copy and paste of SCTP and a good part of it remained as SCTP. Note: the second and third images are taken from a 2.8 system.

2014-09-18T14:44:58Z

This was a copy and paste of SCTP and a good part of it remained as SCTP. Note: the second and third images are taken from a 2.8 system.

← Older revision		Revision as of 10:44, 18 September 2014
Line 1:		Line 1:
	=== '''''Applies to version(s): v2.7.''''' ===		=== '''''Applies to version(s): v2.7.''''' ===
	{{DISPLAYTITLE:Creating the ~~SCTP~~ Configuration}}		{{DISPLAYTITLE:Creating the M2PA Configuration}}
	~~Stream Control Transmission Protocol (SCTP), a Transport Layer protocol, ensures reliable, in-sequence transport of messages.~~

	To edit your system's ~~SCTP~~ configuration:		To edit your system's M2PA configuration:

	1- Select '''~~SCTP~~''' from the navigation panel		1- Select '''M2PA''' from the navigation panel

	[[Image:M2pa_0.png]]		[[Image:M2pa_0.png]]
Line 12:		Line 12:

	* Make sure the box labelled '''Enabled''' is '''checked'''		* Make sure the box labelled '''Enabled''' is '''checked'''
	* Enter a '''name''' for the ~~SCTP~~ service		* Enter a '''name''' for the M2PA service
	* Select an appropriate '''service type''':
	** [[RAW IP\|RAW_IP]]
	** [[UDP IP\|UDP]]
	* Click '''Create'''		* Click '''Create'''

	[[Image:~~Toolpack_v2.5_Creating_SCTP~~.png]]		[[Image:CreateM2pa_1.png]]

	3- Verify that the '''"Sctp Cfg was successfully created"''' message appears		3- Verify that the '''"Sctp Cfg was successfully created"''' message appears

	[[Image:~~Toolpack_v2.5_SCTP_Created~~.png]]		[[Image:CreateM2pa_2.png]]

Allyntree: Created page with "=== '''''Applies to version(s): v2.7.''''' === {{DISPLAYTITLE:Creating the SCTP Configuration}} Stream Control Transmission Protocol (SCTP), a Transport Layer protocol, ensure..."

2013-07-15T14:51:02Z

Created page with "=== '''''Applies to version(s): v2.7.''''' === {{DISPLAYTITLE:Creating the SCTP Configuration}} Stream Control Transmission Protocol (SCTP), a Transport Layer protocol, ensure..."

New page

=== '''''Applies to version(s): v2.7.''''' ===
{{DISPLAYTITLE:Creating the SCTP Configuration}}
Stream Control Transmission Protocol (SCTP), a Transport Layer protocol, ensures reliable, in-sequence transport of messages.

To edit your system's SCTP configuration:

1- Select '''SCTP''' from the navigation panel

[[Image:M2pa_0.png]]

2- Configure the SCTP service

* Make sure the box labelled '''Enabled''' is '''checked'''
* Enter a '''name''' for the SCTP service
* Select an appropriate '''service type''':
** [[RAW IP|RAW_IP]]
** [[UDP IP|UDP]]
* Click '''Create'''

[[Image:Toolpack_v2.5_Creating_SCTP.png]]

3- Verify that the '''"Sctp Cfg was successfully created"''' message appears

[[Image:Toolpack_v2.5_SCTP_Created.png]]

==List of Parameter==

* [[Parameter: Name|Name]]
* [[Parameter: Service Type|Service Type]]