Toolpack:Creating an SCCP LSAP B - Revision history

Allyntree: /* List of Parameters */ Added Max Msg Length parameter

2015-09-30T18:57:56Z

List of Parameters: Added Max Msg Length parameter

← Older revision		Revision as of 14:57, 30 September 2015
Line 42:		Line 42:

	* [[Parameter: Name\|Name]]		* [[Parameter: Name\|Name]]

			'''Advanced Parameters'''
			* [[Parameter: Max Msg Length\|Max Msg Length]]

Allyntree at 17:22, 26 September 2014

2014-09-26T17:22:42Z

← Older revision		Revision as of 13:22, 26 September 2014
Line 28:		Line 28:

	* Enter a [[Parameter: Name\|Name]] for the LSAP		* Enter a [[Parameter: Name\|Name]] for the LSAP
	* Click '''~~Save~~'''		* Click '''Create'''

	[[Image:Create_SCCP_LSAP_1.png]]		[[Image:Create_SCCP_LSAP_1.png]]

Allyntree at 17:22, 26 September 2014

2014-09-26T17:22:15Z

← Older revision		Revision as of 13:22, 26 September 2014
Line 1:		Line 1:
	=== '''''Applies to version(s): v2.~~5, v2.6, 2.7~~''''' ===		=== '''''Applies to version(s): v2.8''''' ===
	{{DISPLAYTITLE:Creating an SCCP LSAP}}		{{DISPLAYTITLE:Creating an SCCP LSAP}}
	~~Now that~~ you ~~have created~~ an [[SCCP]] network, you must create a new SCCP lower service access point ([[LSAP]]).		After you create an [[SCCP]] network, you must create a new SCCP lower service access point ([[LSAP]]).

	Creating an [[Toolpack:Create_an_SCCP_LSAP\|LSAP]] tells the [[SCCP]] protocol layer about a collection of [[SS7]] nodes that are accessible through [[MTP3 Layer\|MTP3]].		Creating an [[Toolpack:Create_an_SCCP_LSAP\|LSAP]] tells the [[SCCP]] protocol layer about a collection of [[SS7]] nodes that are accessible through [[MTP3 Layer\|MTP3]].

Allyntree: New 2.8 article

2014-09-26T17:18:14Z

New 2.8 article

← Older revision		Revision as of 13:18, 26 September 2014
Line 22:		Line 22:


	[[Image:~~Toolpack_v2.5_Create_SCCP_LSAP~~.png]]		[[Image:Create_SCCP_LSAP_0.png]]


Line 30:		Line 30:
	* Click '''Save'''		* Click '''Save'''

	[[Image:~~Toolpack_v2.5_Creating_SCCP_LSAP~~.png]]		[[Image:Create_SCCP_LSAP_1.png]]


	5- Verify that the '''"SccpLsap was successfully created"''' message appears		5- Verify that the '''"SccpLsap was successfully created"''' message appears

	[[Image:~~Toolpack_v2.5_SCCP_LSAP_Created~~.png]]
			[[Image:Create_SCCP_LSAP_2.png]]

Allyntree: New 2.8 article

2014-09-26T17:17:07Z

New 2.8 article

New page

=== '''''Applies to version(s): v2.5, v2.6, 2.7''''' ===
{{DISPLAYTITLE:Creating an SCCP LSAP}}
Now that you have created an [[SCCP]] network, you must create a new SCCP lower service access point ([[LSAP]]).

Creating an [[Toolpack:Create_an_SCCP_LSAP|LSAP]] tells the [[SCCP]] protocol layer about a collection of [[SS7]] nodes that are accessible through [[MTP3 Layer|MTP3]].

To Create an SCCP LSAP:

1- Select '''SCCP''' from the navigation panel

[[Image:Create_SCCP_Stack_0.png]]

2- Select an SCCP Network

[[Image:Select_SCCP_Network_0.png]]

3- Click '''Create New SCCP LSAP''' in the [[SCCP]] network configuration window

[[Image:Toolpack_v2.5_Create_SCCP_LSAP.png]]

4- Configure the new SCCP LSAP:

* Enter a [[Parameter: Name|Name]] for the LSAP
* Click '''Save'''

[[Image:Toolpack_v2.5_Creating_SCCP_LSAP.png]]

5- Verify that the '''"SccpLsap was successfully created"''' message appears

[[Image:Toolpack_v2.5_SCCP_LSAP_Created.png]]

==List of Parameters==

* [[Parameter: Name|Name]]