Allyntree at 17:57, 24 June 2024

2024-06-24T17:57:02Z

← Older revision		Revision as of 13:57, 24 June 2024
Line 7:		Line 7:
	\|-		\|-
	\|Tmedia		\|Tmedia
	\|2.9, 2~~.10~~, 3.0, 3.2		\|3.0, 3.2, 3.3
	\|}		\|}

Luc Morissette: Changed to STP. Added parameter "SG Passthrough Mode"

2023-06-13T15:28:10Z

Changed to STP. Added parameter "SG Passthrough Mode"

New page

{{DISPLAYTITLE:Creating an MTP3 Configuration for STP}}
{| class="wikitable"
|-
|rowspan="3"|This article applies to:
|'''Product'''
|'''Version'''
|-
|Tmedia
|2.9, 2.10, 3.0, 3.2
|}

Once you have set up the MTP2 layer of your SS7 system, you must create an MTP3 configuration.
[[MTP3_Layer|MTP3]] provides message routing between signaling points in an SS7 network.
*'''Note:''' When creating an STP configuration (MTP3 routing), we need to add specific options in the configuration.
<br>
To create an MTP3 configuration for STP:

1- Select '''MTP3''' from the navigation panel

[[Image:Mtp3_0_A.png]]

2- Configure the new MTP3 service:

* Enter a '''name''' for the MTP3 configuration
* Make sure the '''Enabled''' and '''SSf Validation''' boxes are checked
* Select '''STP''' as the '''signaling point type'''
* Click '''Create'''

[[Image:MTP3_STP_config_1_A.png]]

3- Verify that the '''"Mtp3Cfg was successfully created"''' message appears

[[Image:Mtp3_2_A.png]]

<div class="mw-collapsible mw-collapsed" data-collapsetext="Northbound Interface" data-expandtext="Northbound Interface" style="width: 400px;">

'''Path'''
<pre>
/configurations/@[configuration_name]/mtp3_stacks/@[mtp3_name]
</pre>

'''Parameters (text)'''
<pre>
/configurations/@[configuration_name]/mtp3_stacks/@[mtp3_name]
enabled = true
name = "@[mtp3_name]"
signaling_point_type = "SP"

/configurations/@[configuration_name]/mtp3_stacks/@[mtp3_name]/advanced_parameters
ssf_validation = true
transfer_restrict_required = false

/configurations/@[configuration_name]/mtp3_stacks/@[mtp3_name]/timers
t15_timer = "2 seconds"
t16_timer = "1400 milliseconds"
t18_timer = "11 seconds"
t19_timer = "67 seconds"
t21_timer = "63 seconds"
t26_timer = "12 seconds"
</pre>

'''Parameters (json)'''
<pre>
{
"advanced_parameters" : {
"ssf_validation" : true,
"transfer_restrict_required" : false
},
"enabled" : true,
"name" : "@[mtp3_name]",
"signaling_point_type" : "SP",
"timers" : {
"t15_timer" : "2 seconds",
"t16_timer" : "1400 milliseconds",
"t18_timer" : "11 seconds",
"t19_timer" : "67 seconds",
"t21_timer" : "63 seconds",
"t26_timer" : "12 seconds"
}
}
</pre>
</div>

==List of Parameters==
* [[Parameter: Name|Name]]
* [[Parameter: Enabled|Enabled]]
* [[Parameter: Signaling Point Type|Signaling Point Type]]

'''Timers'''
* [[Parameter: MTP3 T15 Timer|T15 Timer]]
* [[Parameter: MTP3 T16 Timer|T16 Timer]]
* [[Parameter: MTP3 T18 Timer|T18 Timer]]
* [[Parameter: MTP3 T19 Timer|T19 Timer]]
* [[Parameter: MTP3 T21 Timer|T21 Timer]]
* [[Parameter: MTP3 T26 Timer|T26 Timer]]

'''Advanced Parameters'''
* [[Parameter: MTP3 Ssf Validation|Ssf Validation]]
* [[Parameter: MTP3 Transfer Restricted required|Transfer Restricted required]]
* [[Parameter: SG Passthrough Mode|SG Passthrough Mode]]

Toolpack:Creating an MTP3 Configuration for STP - Revision history

Allyntree at 17:57, 24 June 2024

Luc Morissette: Changed to STP. Added parameter "SG Passthrough Mode"