Toolpack:Creating an MTP3 Configuration D - Revision history

Allyntree: /* List of Parameters */ Modified parameter links. Grouped Timers into its own category

2015-09-02T13:54:24Z

List of Parameters: Modified parameter links. Grouped Timers into its own category

← Older revision		Revision as of 09:54, 2 September 2015
Line 24:		Line 24:

	==List of Parameters==		==List of Parameters==

	* [[Parameter: Name\|Name]]		* [[Parameter: Name\|Name]]
	* [[Parameter: Enabled\|Enabled]]		* [[Parameter: Enabled\|Enabled]]
	* [[Parameter: SSf Validation\|SSf Validation]]
	* [[Parameter: Signaling Point Type\|Signaling Point Type]]		* [[Parameter: Signaling Point Type\|Signaling Point Type]]

			'''Timers'''
	* [[Parameter: MTP3 T15 Timer\|T15 Timer]]		* [[Parameter: MTP3 T15 Timer\|T15 Timer]]
	* [[Parameter: MTP3 T16 Timer\|T16 Timer]]		* [[Parameter: MTP3 T16 Timer\|T16 Timer]]
Line 36:		Line 36:
	* [[Parameter: MTP3 T26 Timer\|T26 Timer]]		* [[Parameter: MTP3 T26 Timer\|T26 Timer]]

	Advanced Parameters		'''Advanced Parameters'''
	* [[Parameter: MTP3 Ssf Validation\|Ssf Validation]]		* [[Parameter: MTP3 Ssf Validation\|Ssf Validation]]
	* [[Parameter: Restart Procedure\|Restart Procedure]]
	* [[Parameter: MTP3 Transfer Restricted required\|Transfer Restricted required]]		* [[Parameter: MTP3 Transfer Restricted required\|Transfer Restricted required]]

Allyntree: /* Applies to version(s): v2.8 */ Revised step 2 and changed its screenshot.

2015-09-02T13:50:25Z

Applies to version(s): v2.8: Revised step 2 and changed its screenshot.

← Older revision		Revision as of 09:50, 2 September 2015
Line 15:		Line 15:
	* Make sure the '''Enabled''' and '''SSf Validation''' boxes are checked		* Make sure the '''Enabled''' and '''SSf Validation''' boxes are checked
	* Select '''SP''' as the '''signaling point type'''		* Select '''SP''' as the '''signaling point type'''
	* Select a '''restart procedure'''
	* Click '''Create'''		* Click '''Create'''

Allyntree: New 2.8 artic;e

2014-09-09T13:47:29Z

New 2.8 artic;e

New page

=== '''''Applies to version(s): v2.8''''' ===
{{DISPLAYTITLE:Creating an MTP3 Configuration}}
Once you have set up the MTP2 layer of your SS7 system, you must create an MTP3 configuration.
[[MTP3_Layer|MTP3]] provides message routing between signaling points in an SS7 network.

To create an MTP3 configuration:

1- Select '''MTP3''' from the navigation panel

[[Image:Mtp3_0_A.png]]

2- Configure the new MTP3 service:

* Enter a '''name''' for the MTP3 configuration
* Make sure the '''Enabled''' and '''SSf Validation''' boxes are checked
* Select '''SP''' as the '''signaling point type'''
* Select a '''restart procedure'''
* Click '''Create'''

[[Image:Mtp3_1_A.png]]

3- Verify that the '''"Mtp3Cfg was successfully created"''' message appears

[[Image:Mtp3_2_A.png]]

==List of Parameters==

* [[Parameter: Name|Name]]
* [[Parameter: Enabled|Enabled]]
* [[Parameter: SSf Validation|SSf Validation]]
* [[Parameter: Signaling Point Type|Signaling Point Type]]
* [[Parameter: MTP3 T15 Timer|T15 Timer]]
* [[Parameter: MTP3 T16 Timer|T16 Timer]]
* [[Parameter: MTP3 T18 Timer|T18 Timer]]
* [[Parameter: MTP3 T19 Timer|T19 Timer]]
* [[Parameter: MTP3 T21 Timer|T21 Timer]]
* [[Parameter: MTP3 T26 Timer|T26 Timer]]

Advanced Parameters
* [[Parameter: MTP3 Ssf Validation|Ssf Validation]]
* [[Parameter: Restart Procedure|Restart Procedure]]
* [[Parameter: MTP3 Transfer Restricted required|Transfer Restricted required]]