Toolpack:Creating an ISUP Interface B - Revision history

Allyntree: /* List of Parameters */

2015-09-17T15:57:25Z

List of Parameters

← Older revision		Revision as of 11:57, 17 September 2015
Line 47:		Line 47:
	* [[Parameter: Origin Point Code\|OPC]]		* [[Parameter: Origin Point Code\|OPC]]
	* [[Parameter: Destination Point Code\|DPC]]		* [[Parameter: Destination Point Code\|DPC]]


			'''Timers'''
			* [[Parameter: IsupNetwork_T4 Timer\|T4 Timer]]
			* [[Parameter: Pause Timer\|Pause Timer]]
			* [[Parameter: DPC Status Query Timer\|DPC Status Query Timer]]


			'''Advanced Parameters'''
			* [[Parameter: Pause Action\|Pause Action]]
			* [[Parameter: Available Test\|Available Test]]
			* [[Parameter: Sls Selector\|Sls Selector]]
			* [[Parameter: Sls Range\|Sls Range]]

Allyntree at 13:59, 18 September 2014

2014-09-18T13:59:40Z

← Older revision		Revision as of 09:59, 18 September 2014
Line 8:		Line 8:
	To create an ISUP interface:		To create an ISUP interface:

	1- Click '''ISUP''' in the navigation ~~pane~~.		1- Click '''ISUP''' in the navigation panel.

	[[Image:CreateIsupStack_0.png]]		[[Image:CreateIsupStack_0.png]]

Allyntree: /* Applies to version(s): v2.8 */

2014-09-17T16:56:58Z

Applies to version(s): v2.8

← Older revision		Revision as of 12:56, 17 September 2014
Line 1:		Line 1:
	=== '''''Applies to version(s): v2.8''''' ===		=== '''''Applies to version(s): v2.8''''' ===
	{{DISPLAYTITLE:Creating an ISUP Interface}}		{{DISPLAYTITLE:Creating an ISUP Interface}}
	~~Now that you have created an [[ISUP]] user part to contain them, you must create new ISUP interfaces.~~

	The [[ISUP]] interface creates a binding within the ISUP layer of a particular variant, a specific network, and an OPC/DPC pair to which circuits can be assigned.		The [[ISUP]] interface creates a binding within the ISUP layer of a particular variant, a specific network, and an OPC/DPC pair to which circuits can be assigned. It contains the circuit identifier codes (CICs) within the ISUP user part. One interface is created for each similar grouping of CICs within one user part protocol variant.

	~~The ISUP interface contains the circuit identifier codes (CICs) within the~~ ISUP user part~~. One interface is created for each similar grouping of CICs within~~ one ~~user part protocol variant~~.		After you have created an [[ISUP]] user part, you must create one or more ISUP interfaces.

	To create an ISUP interface:		To create an ISUP interface:
Line 40:		Line 39:

	[[Image:Create_ISUP_Interface_2.png]]		[[Image:Create_ISUP_Interface_2.png]]


	==List of Parameters==		==List of Parameters==

Allyntree at 16:53, 17 September 2014

2014-09-17T16:53:09Z

← Older revision		Revision as of 12:53, 17 September 2014
Line 1:		Line 1:
	=== '''''Applies to version(s): v2.~~5, v2.6., v2.7~~''''' ===		=== '''''Applies to version(s): v2.8''''' ===
	{{DISPLAYTITLE:Creating an ISUP Interface}}		{{DISPLAYTITLE:Creating an ISUP Interface}}
	Now that you have created an [[ISUP]] user part to contain them, you must create new ISUP interfaces.		Now that you have created an [[ISUP]] user part to contain them, you must create new ISUP interfaces.
Line 21:		Line 21:
	3- Click '''Create New Isup Interface''' in the ISUP stack configuration window		3- Click '''Create New Isup Interface''' in the ISUP stack configuration window

	[[Image:~~Toolpack_v2.5_Create_ISUP_Interface~~.png]]		[[Image:Create_ISUP_Interface_0.png]]


Line 34:		Line 34:
	* Click '''Create'''		* Click '''Create'''

	[[Image:~~Toolpack_v2.5_Creating_ISUP_Interface~~.png]]		[[Image:Create_ISUP_Interface_1.png]]


	5- Verify that the '''"IsupInterface was successfully created"''' message appears		5- Verify that the '''"IsupInterface was successfully created"''' message appears

	[[Image:~~Toolpack_v2.5_ISUP_Interface_Created~~.png]]		[[Image:Create_ISUP_Interface_2.png]]

Allyntree: new 2.8 article: in process

2014-09-17T16:51:15Z

new 2.8 article: in process

New page

=== '''''Applies to version(s): v2.5, v2.6., v2.7''''' ===
{{DISPLAYTITLE:Creating an ISUP Interface}}
Now that you have created an [[ISUP]] user part to contain them, you must create new ISUP interfaces.

The [[ISUP]] interface creates a binding within the ISUP layer of a particular variant, a specific network, and an OPC/DPC pair to which circuits can be assigned.

The ISUP interface contains the circuit identifier codes (CICs) within the ISUP user part. One interface is created for each similar grouping of CICs within one user part protocol variant.

To create an ISUP interface:

1- Click '''ISUP''' in the navigation pane.

[[Image:CreateIsupStack_0.png]]

2- Select the ISUP stack

[[Image:SelectIsupStack_0.png]]

3- Click '''Create New Isup Interface''' in the ISUP stack configuration window

[[Image:Toolpack_v2.5_Create_ISUP_Interface.png]]

4- Configure the new ISUP interface:

* Enter a '''name''' for the interface
* Select an '''ISUP user part'''
* Select an '''ISUP network'''
* Select a '''trunk type'''
* Select an '''originating point code''' (OPC)
* Select a '''destination point code''' (DPC)
* Click '''Create'''

[[Image:Toolpack_v2.5_Creating_ISUP_Interface.png]]

5- Verify that the '''"IsupInterface was successfully created"''' message appears

[[Image:Toolpack_v2.5_ISUP_Interface_Created.png]]

==List of Parameters==

* [[Parameter: Name|Name]]
* [[Parameter: ISUP User Part|ISUP User Part]]
* [[Parameter: ISUP Network|ISUP Network]]
* [[Parameter: Origin Point Code|OPC]]
* [[Parameter: Destination Point Code|DPC]]