Toolpack:Creating a N+1 Group B - Revision history

Allyntree: /* Applies to version v2.8 */

2014-11-24T15:27:17Z

Applies to version v2.8

← Older revision		Revision as of 11:27, 24 November 2014
Line 28:		Line 28:


	4- Verify that the '''N+1 Group was successfully ~~added~~''' message is displayed.		4- Verify that the '''N+1 Group was successfully created''' message is displayed.

	[[Image:N_Plus_One_3_A.png]]		[[Image:N_Plus_One_3_A.png]]

Allyntree: /* Applies to version v2.8 */

2014-11-24T15:26:34Z

Applies to version v2.8

← Older revision		Revision as of 11:26, 24 November 2014
Line 7:		Line 7:

	1- Click '''N+1''' in the navigation panel		1- Click '''N+1''' in the navigation panel


	[[Image:N_Plus_One_0_A.png]]		[[Image:N_Plus_One_0_A.png]]
Line 13:		Line 12:

	2- Click '''Create New N+1 Group'''		2- Click '''Create New N+1 Group'''


	[[Image:N_Plus_One_1_A.png]]		[[Image:N_Plus_One_1_A.png]]
Line 30:		Line 28:


	4- Verify that ~~the newly added N+1 patch panel appears in~~ the '''N+1 ~~Groups~~''' ~~list~~.		4- Verify that the '''N+1 Group was successfully added''' message is displayed.


	[[Image:N_Plus_One_3_A.png]]		[[Image:N_Plus_One_3_A.png]]

Allyntree: /* Applies to version v2.8 */

2014-11-24T15:24:15Z

Applies to version v2.8

← Older revision		Revision as of 11:24, 24 November 2014
Line 2:		Line 2:
	{{DISPLAYTITLE:Creating an N+1 Group}}		{{DISPLAYTITLE:Creating an N+1 Group}}

	Once the N+1 patch panel is created, you must ~~create~~ an N+1 group to assign each hardware unit to their correct position.		Once the N+1 patch panel is created, you must configure an N+1 group and assign each hardware unit to their correct position on the N+1 pacth panel.

	'''To create an N+1 Patch Panel:'''		'''To create an N+1 Patch Panel:'''

Allyntree: Revised the text and provided a more realistic screen shoot.

2014-11-24T15:23:15Z

Revised the text and provided a more realistic screen shoot.

← Older revision		Revision as of 11:23, 24 November 2014
Line 19:		Line 19:

	3- Set the correct serial numbers for units that are assigned as Primary and Secondary N+1 Patch panels, as well as the N+1 Backup unit.		3- Set the correct serial numbers for units that are assigned as Primary and Secondary N+1 Patch panels, as well as the N+1 Backup unit.
			*Configure the following:
			**Primary N+1 Patch Panel: N+1 patch panel for the main fiber
			**Secondary N+1 Patch Panel: N+1 patch panel for the APS
			**N+1 Backup Unit: Standby unit
			**Auto switch-back: Select this option to automatically switch TDM and VoIP media back to the original unit when it becomes available. If this option is not selected, then the backkup unit will remain active until it is manually rebooted.
			**Port 0 to 14: Units must be listed as they are physically connected to the N+1 patch panel.
	* Click '''Create'''		* Click '''Create'''


	[[Image:N_Plus_One_2_A.png]]		[[Image:N_Plus_One_2_A.png]]

Allyntree: /* Applies to version v2.8 */ Modified step 3 instruction

2014-08-25T13:28:37Z

Applies to version v2.8: Modified step 3 instruction

← Older revision		Revision as of 09:28, 25 August 2014
Line 18:		Line 18:


	3- Set the correct serial ~~number of a~~ unit ~~to the correct patch panel port~~.		3- Set the correct serial numbers for units that are assigned as Primary and Secondary N+1 Patch panels, as well as the N+1 Backup unit.
	* Click '''Create'''		* Click '''Create'''

Allyntree: New Arcticle

2014-08-25T13:10:27Z

New Arcticle

New page

=== '''''Applies to version v2.8''''' ===
{{DISPLAYTITLE:Creating an N+1 Group}}

Once the N+1 patch panel is created, you must create an N+1 group to assign each hardware unit to their correct position.

'''To create an N+1 Patch Panel:'''

1- Click '''N+1''' in the navigation panel

[[Image:N_Plus_One_0_A.png]]

2- Click '''Create New N+1 Group'''

[[Image:N_Plus_One_1_A.png]]

3- Set the correct serial number of a unit to the correct patch panel port.
* Click '''Create'''

[[Image:N_Plus_One_2_A.png]]

4- Verify that the newly added N+1 patch panel appears in the '''N+1 Groups''' list.

[[Image:N_Plus_One_3_A.png]]