Toolpack:Creating a 1+1 Group B - Revision history

Allyntree: /* Applies to version v2.8 */

2015-06-04T15:05:06Z

Applies to version v2.8

← Older revision		Revision as of 11:05, 4 June 2015
Line 29:		Line 29:

	[[Image:Create1and1Group_3_B.png]]		[[Image:Create1and1Group_3_B.png]]

			==List of Parameters==

			* [[Parameter: Name\|Name]]
			* [[Parameter: Serial\|Serial]]
			* [[Parameter: Adapter Type\|Type]]
			* [[Parameter: Auto Switch-Back\|Auto Switch-Back]]

Allyntree: Formatting

2015-06-01T17:38:26Z

Formatting

← Older revision		Revision as of 13:38, 1 June 2015
Line 26:		Line 26:


	4- Verify that the newly added 1+1 group appears in the '''1+1 Groups ~~List~~'''		4- Verify that the newly added 1+1 group appears in the '''1+1 Groups''' list.

	[[Image:Create1and1Group_3_B.png]]		[[Image:Create1and1Group_3_B.png]]

Allyntree: Save -> Create

2015-06-01T17:34:08Z

Save -> Create

← Older revision		Revision as of 13:34, 1 June 2015
Line 21:		Line 21:
	* Select the '''serial number''' of the 1+1 backup hardware device.		* Select the '''serial number''' of the 1+1 backup hardware device.
	* Set '''Auto switch-back''' to cause an automatic switch back to the original primary hardware device when it becomes available. If the field is clear (not checked), then a switch back to the original device will occur only after a manual reboot of the system.		* Set '''Auto switch-back''' to cause an automatic switch back to the original primary hardware device when it becomes available. If the field is clear (not checked), then a switch back to the original device will occur only after a manual reboot of the system.
	* Click '''~~Save~~'''		* Click '''Create'''

	[[Image:Create1and1Group_2_B.png]]		[[Image:Create1and1Group_2_B.png]]

Allyntree: /* Applies to version v2.8 */

2015-01-20T15:40:20Z

Applies to version v2.8

← Older revision		Revision as of 11:40, 20 January 2015
Line 2:		Line 2:
	{{DISPLAYTITLE:Creating a 1+1 Group}}		{{DISPLAYTITLE:Creating a 1+1 Group}}

	A 1+1 group indentifies the two Tmedia hardware devices that ~~will~~ operate together to provide 1+1 backup protection. One device is identified as the primary hardware device, while the other device is identified as the backup hardware device. To create a 1+1 group, you must use the Tmedia [[Web Portal]].		A 1+1 group indentifies the two Tmedia hardware devices that operate together to provide 1+1 backup protection. One device is identified as the primary hardware device, while the other device is identified as the backup hardware device. To create a 1+1 group, you must use the Tmedia [[Web Portal]].

	'''To create a 1+1 group:'''		'''To create a 1+1 group:'''

	1- Click '''1+1 ~~Groups~~''' in the navigation panel		1- Click '''1+1''' in the navigation panel

	[[Image:Create1and1Group_0_B.png]]		[[Image:Create1and1Group_0_B.png]]

Allyntree: Minor edits

2015-01-20T15:36:06Z

Minor edits

← Older revision		Revision as of 11:36, 20 January 2015
Line 7:		Line 7:

	1- Click '''1+1 Groups''' in the navigation panel		1- Click '''1+1 Groups''' in the navigation panel


	[[Image:Create1and1Group_0_B.png]]		[[Image:Create1and1Group_0_B.png]]
Line 13:		Line 12:

	2- Click '''Create New 1+1 Group'''		2- Click '''Create New 1+1 Group'''


	[[Image:Create1and1Group_1_B.png]]		[[Image:Create1and1Group_1_B.png]]


	3- Enter the serial numbers of the ~~Primary~~ and ~~Backup Hardware~~ devices.		3- Enter the serial numbers of the primary and 1+1 backup hardware devices.
			* Provide a name for the 1+1 group.
	* Select the '''serial number''' of the primary hardware device. (This field may already be filled.)		* Select the '''serial number''' of the primary hardware device. (This field may already be filled.)
	* Select the '''serial number''' of the backup hardware device.		* Select the '''serial number''' of the 1+1 backup hardware device.
	* Set '''Auto switch-back''' to cause an automatic switch back to the original primary hardware device when it becomes available. If the field is clear (not checked), then a switch back to the original device will occur only after a manual reboot of the system.		* Set '''Auto switch-back''' to cause an automatic switch back to the original primary hardware device when it becomes available. If the field is clear (not checked), then a switch back to the original device will occur only after a manual reboot of the system.
	* Click '''Save'''		* Click '''Save'''


	[[Image:Create1and1Group_2_B.png]]		[[Image:Create1and1Group_2_B.png]]
Line 30:		Line 27:

	4- Verify that the newly added 1+1 group appears in the '''1+1 Groups List'''		4- Verify that the newly added 1+1 group appears in the '''1+1 Groups List'''


	[[Image:Create1and1Group_3_B.png]]		[[Image:Create1and1Group_3_B.png]]

Allyntree: New Article: Place holder for 2.8

2014-08-25T12:57:22Z

New Article: Place holder for 2.8

New page

=== '''''Applies to version v2.8''''' ===
{{DISPLAYTITLE:Creating a 1+1 Group}}

A 1+1 group indentifies the two Tmedia hardware devices that will operate together to provide 1+1 backup protection. One device is identified as the primary hardware device, while the other device is identified as the backup hardware device. To create a 1+1 group, you must use the Tmedia [[Web Portal]].

'''To create a 1+1 group:'''

1- Click '''1+1 Groups''' in the navigation panel

[[Image:Create1and1Group_0_B.png]]

2- Click '''Create New 1+1 Group'''

[[Image:Create1and1Group_1_B.png]]

3- Enter the serial numbers of the Primary and Backup Hardware devices.

* Select the '''serial number''' of the primary hardware device. (This field may already be filled.)
* Select the '''serial number''' of the backup hardware device.
* Set '''Auto switch-back''' to cause an automatic switch back to the original primary hardware device when it becomes available. If the field is clear (not checked), then a switch back to the original device will occur only after a manual reboot of the system.
* Click '''Save'''

[[Image:Create1and1Group_2_B.png]]

4- Verify that the newly added 1+1 group appears in the '''1+1 Groups List'''

[[Image:Create1and1Group_3_B.png]]