Toolpack:Creating a 1+1 Group A - Revision history

Allyntree at 16:17, 5 July 2013

2013-07-05T16:17:03Z

← Older revision		Revision as of 12:17, 5 July 2013
Line 1:		Line 1:
	=== '''''Applies to version v2.6''''' ===		=== '''''Applies to version v2.6, v2.7''''' ===
	{{DISPLAYTITLE:Creating a 1+1 Group}}		{{DISPLAYTITLE:Creating a 1+1 Group}}

Allyntree: /* Applies to version v2.6 */

2012-10-21T16:43:08Z

Applies to version v2.6

← Older revision		Revision as of 12:43, 21 October 2012
Line 22:		Line 22:
	* Select the '''serial number''' of the primary hardware device. (This field may already be filled.)		* Select the '''serial number''' of the primary hardware device. (This field may already be filled.)
	* Select the '''serial number''' of the backup hardware device.		* Select the '''serial number''' of the backup hardware device.
	* Set '''Auto switch-back''' to cause an automatic switch back to the original primary hardware device when it becomes available. If the field is clear (not checked), then ~~aswitch~~ back to the original device will occur only after a manual reboot of the system.		* Set '''Auto switch-back''' to cause an automatic switch back to the original primary hardware device when it becomes available. If the field is clear (not checked), then a switch back to the original device will occur only after a manual reboot of the system.
	* Click '''Save'''		* Click '''Save'''

Allyntree: /* Applies to version v2.6 */

2012-10-21T16:42:23Z

Applies to version v2.6

← Older revision		Revision as of 12:42, 21 October 2012
Line 2:		Line 2:
	{{DISPLAYTITLE:Creating a 1+1 Group}}		{{DISPLAYTITLE:Creating a 1+1 Group}}

	A 1+1 group indentifies the two Tmedia hardware devices that will operate together to provide 1+1 backup protection. One device is identified as the primary hardware device while the other device is identified as the backup hardware device. To create a 1+1 group, you must use the Tmedia [[Web Portal]].		A 1+1 group indentifies the two Tmedia hardware devices that will operate together to provide 1+1 backup protection. One device is identified as the primary hardware device, while the other device is identified as the backup hardware device. To create a 1+1 group, you must use the Tmedia [[Web Portal]].

	'''To create a 1+1 group:'''		'''To create a 1+1 group:'''
Line 22:		Line 22:
	* Select the '''serial number''' of the primary hardware device. (This field may already be filled.)		* Select the '''serial number''' of the primary hardware device. (This field may already be filled.)
	* Select the '''serial number''' of the backup hardware device.		* Select the '''serial number''' of the backup hardware device.
	* Set '''Auto switch-back''' to ~~automatically~~ switch back to the original primary hardware device when it becomes available. If the field is clear (not checked), then ~~the swicth~~ back to the original device will occur only after a manual reboot of the system.		* Set '''Auto switch-back''' to cause an automatic switch back to the original primary hardware device when it becomes available. If the field is clear (not checked), then aswitch back to the original device will occur only after a manual reboot of the system.
	* Click '''Save'''		* Click '''Save'''

Allyntree: Created page with "=== '''''Applies to version v2.6''''' === {{DISPLAYTITLE:Creating a 1+1 Group}} A 1+1 group indentifies the two Tmedia hardware devices that will operate together to provide ..."

2012-10-21T16:40:14Z

Created page with "=== '''''Applies to version v2.6''''' === {{DISPLAYTITLE:Creating a 1+1 Group}} A 1+1 group indentifies the two Tmedia hardware devices that will operate together to provide ..."

New page

=== '''''Applies to version v2.6''''' ===
{{DISPLAYTITLE:Creating a 1+1 Group}}

A 1+1 group indentifies the two Tmedia hardware devices that will operate together to provide 1+1 backup protection. One device is identified as the primary hardware device while the other device is identified as the backup hardware device. To create a 1+1 group, you must use the Tmedia [[Web Portal]].

'''To create a 1+1 group:'''

1- Click '''1+1 Groups''' in the navigation panel

[[Image:Create1and1Group_0_A.png]]

2- Click '''Create New 1+1 Group'''

[[Image:Create1and1Group_1_A.png]]

3- Enter the serial numbers of the Primary and Backup Hardware devices.

* Select the '''serial number''' of the primary hardware device. (This field may already be filled.)
* Select the '''serial number''' of the backup hardware device.
* Set '''Auto switch-back''' to automatically switch back to the original primary hardware device when it becomes available. If the field is clear (not checked), then the swicth back to the original device will occur only after a manual reboot of the system.
* Click '''Save'''

[[Image:Create1and1Group_2_A.png]]

4- Verify that the newly added 1+1 group appears in the '''1+1 Groups List'''

[[Image:Create1and1Group_3_A.png]]