Toolpack:Creating SS7 Point Codes E - Revision history

Allyntree at 17:52, 24 June 2024

2024-06-24T17:52:18Z

← Older revision		Revision as of 13:52, 24 June 2024
Line 7:		Line 7:
	\|-		\|-
	\|Tmedia		\|Tmedia
	\|2.10, 3.0, 3.2		\|3.0, 3.2, 3.3
	\|}		\|}

Allyntree at 18:39, 25 November 2020

2020-11-25T18:39:02Z

← Older revision		Revision as of 14:39, 25 November 2020
Line 1:		Line 1:
	~~=== '''''Applies to version(s): 2.10, 3.0, 3.2''''' ===~~
	{{DISPLAYTITLE:Creating SS7 Point Codes}}		{{DISPLAYTITLE:Creating SS7 Point Codes}}
			{\| class="wikitable"
			\|-
			\|rowspan="3"\|This article applies to:
			\|'''Product'''
			\|'''Version'''
			\|-
			\|Tmedia
			\|2.10, 3.0, 3.2
			\|}

	Point codes are used to define the adjacent and target networks so that calls are properly routed from one network to the next.		Point codes are used to define the adjacent and target networks so that calls are properly routed from one network to the next.

Allyntree at 13:41, 21 August 2020

2020-08-21T13:41:28Z

← Older revision		Revision as of 09:41, 21 August 2020
Line 1:		Line 1:
	=== '''''Applies to version(s): v2.10, v3.0''''' ===		=== '''''Applies to version(s): 2.10, 3.0, 3.2''''' ===
	{{DISPLAYTITLE:Creating SS7 Point Codes}}		{{DISPLAYTITLE:Creating SS7 Point Codes}}
	Point codes are used to define the adjacent and target networks so that calls are properly routed from one network to the next.		Point codes are used to define the adjacent and target networks so that calls are properly routed from one network to the next.

Allyntree at 15:42, 29 November 2017

2017-11-29T15:42:51Z

← Older revision		Revision as of 11:42, 29 November 2017
Line 1:		Line 1:
	=== '''''Applies to version(s): v2.10''''' ===		=== '''''Applies to version(s): v2.10, v3.0''''' ===
	{{DISPLAYTITLE:Creating SS7 Point Codes}}		{{DISPLAYTITLE:Creating SS7 Point Codes}}
	Point codes are used to define the adjacent and target networks so that calls are properly routed from one network to the next.		Point codes are used to define the adjacent and target networks so that calls are properly routed from one network to the next.

Allyntree at 15:35, 31 October 2016

2016-10-31T15:35:36Z

← Older revision		Revision as of 11:35, 31 October 2016
Line 1:		Line 1:
	=== '''''Applies to version(s): v2.9.''''' ===		=== '''''Applies to version(s): v2.10''''' ===
	{{DISPLAYTITLE:Creating SS7 Point Codes}}		{{DISPLAYTITLE:Creating SS7 Point Codes}}
	Point codes are used to define the adjacent and target networks so that calls are properly routed from one network to the next.		Point codes are used to define the adjacent and target networks so that calls are properly routed from one network to the next.
Line 23:		Line 23:
	In this example, an originating point code (OPC) is created.		In this example, an originating point code (OPC) is created.

	[[Image:~~PointCodes_2_A~~.png]]		[[Image:PointCodes_2_B.png]]

	4. Verify that the '''"PointCode was successfully created"''' message appears, and the new point code appears in the '''Point Codes''' list		4. Verify that the '''"PointCode was successfully created"''' message appears, and the new point code appears in the '''Point Codes''' list

Allyntree: New article because DPC Length is changed to length

2016-10-31T15:32:45Z

New article because DPC Length is changed to length

New page

=== '''''Applies to version(s): v2.9.''''' ===
{{DISPLAYTITLE:Creating SS7 Point Codes}}
Point codes are used to define the adjacent and target networks so that calls are properly routed from one network to the next.

To create SS7 originating point codes (OPC) and destination point codes (DPC):

1- Click '''Point Codes''' in the navigation panel

[[Image:PointCodes_0_A.png]]

2- Click '''Create New Point Code'''

[[Image:PointCodes_1_A.png]]

3- Configure the new point code:

* Enter a '''name''' for the point code
* Select a point code '''type''' (select type-specific parameters)
* Select a point code '''length''' (14, 16, 24 bits)
* Enter a '''point code'''. Either as bits, decimal, or hexadecimal.
* Click '''Create'''

In this example, an originating point code (OPC) is created.

[[Image:PointCodes_2_A.png]]

4. Verify that the '''"PointCode was successfully created"''' message appears, and the new point code appears in the '''Point Codes''' list

[[Image:PointCodes_3_A.png]]

<div class="mw-collapsible mw-collapsed" data-collapsetext="Northbound Interface" data-expandtext="Northbound Interface" style="width: 400px;">

'''Path'''
<pre>
/configurations/@[configuration_name]/point_codes/@[point_code]
</pre>

'''Parameters (text)'''
<pre>
/configurations/@[configuration_name]/point_codes/@[point_code]
length = "14bits format=3.8.3"
name = "@[point_code]"
point_code = "1.7.2"
type = "OPC"
</pre>

'''Parameters (json)'''
<pre>
{
"length" : "14bits format=3.8.3",
"name" : "@[point_code]",
"point_code" : "1.7.2",
"type" : "OPC"
}
</pre>
</div>

==List of parameters==

* [[Parameter: Name|Name]]
* [[Parameter: Type|Type]]
* [[Parameter: DPC Length|Length]]
* [[Parameter: Point Code|Point Code]]