Allyntree at 17:14, 1 May 2018

2018-05-01T17:14:04Z

Ktrueman: initial content

2009-09-03T17:15:38Z

initial content

New page

This step is used to initialize the userpart parameters of the SCCP layer

WALKTHROUGH AND SCREENSHOT CONTENT ARE OUTSTANDING

== Description of parameters ==
General explanation of the configuration parameters:

*The '''Handle SCCP network''' parameter specifies the handle of the SCCP network
*The '''Unique identifier SCCP Userpart''' parameter specifies the unique ID of the SCCP Userpart for a [[SS7]] system

----

*The '''Message priority''' parameter specifies the priority of messages. Allowable values are as follows:

{| class="wikitable" border="1"
! width="150" style="background:#efefef;" |SCCP Message Priority
! width="350" style="background:#efefef;" |Description
|-
| Highest||
|-
| 0|| Same as highest
|-
| 1||
|-
| 2||
|-
| 3|| Same as lowest
|-
| Lowest||
|}

----

*The '''Connection mode''' parameter specifies the different modes of connection for a SCCP userpart. Allowable values include:

{| class="wikitable" border="1"
! width="150" style="background:#efefef;" |SCCP connection mode
! width="350" style="background:#efefef;" |Description
|-
| TCAP|| SCCP userpart is used in conjunction with an above local TCAP layer and cannot be controlled by the host application but the host application will receive ALARM notifications
|-
| Host TCAP|| SCCP userpart is used as a standalone and communicates with remote TCAP layer (host application)
|}

----

*The '''Subsystem number''' parameter specifies a subsystem number for this userpart. Allowable values are from 1 to 255. See the table for '
SCCP SSN value to identify SCCP user' in [[Toolpack:Create a SCCP route#Description of SSN specific parameters|Toolpack:Create a SCCP route]].
*The '''Number backup point code''' parameter specifies the number of backup point code entries in the Backup Point Code Entries and the Priority Backup Point Code Entries arrays.
*The '''Array of backup point code entries''' parameter specifies the list of backup point code for this Userpart. This parameter is reconfigurable.
*The '''Array of priority of backup point code entries''' parameter specifies the list of priority of each backup point code for this Userpart. Allowable values are from 0 to 255.

'''Note:''' Zero being the lowest priority.

----

*The number concerned point code parameter specifies the number of concerned point code entries in the 'Concerned Point Code Entries' array
*The array of concerned point code entries parameter (specifies the list of concerned point code for this Userpart

[[category:Needs revising]]

← Older revision		Revision as of 13:14, 1 May 2018
Line 1:		Line 1:
	This step is used to initialize the userpart parameters of the SCCP layer		This step is used to initialize the userpart parameters of the SCCP layer



	~~WALKTHROUGH AND SCREENSHOT CONTENT ARE OUTSTANDING~~



	== Description of parameters ==		== Description of parameters ==
	General explanation of the configuration parameters:		General explanation of the configuration parameters:


	*The '''Handle SCCP network''' parameter specifies the handle of the SCCP network		*The '''Handle SCCP network''' parameter specifies the handle of the SCCP network
Line 53:		Line 46:
	\| Host TCAP\|\| SCCP userpart is used as a standalone and communicates with remote TCAP layer (host application)		\| Host TCAP\|\| SCCP userpart is used as a standalone and communicates with remote TCAP layer (host application)
	\|}		\|}


	----		----


	*The '''Subsystem number''' parameter specifies a subsystem number for this userpart. Allowable values are from 1 to 255. See the table for '		*The '''Subsystem number''' parameter specifies a subsystem number for this userpart. Allowable values are from 1 to 255. See the table for '
Line 63:		Line 54:
	*The '''Array of backup point code entries''' parameter specifies the list of backup point code for this Userpart. This parameter is reconfigurable.		*The '''Array of backup point code entries''' parameter specifies the list of backup point code for this Userpart. This parameter is reconfigurable.
	*The '''Array of priority of backup point code entries''' parameter specifies the list of priority of each backup point code for this Userpart. Allowable values are from 0 to 255.		*The '''Array of priority of backup point code entries''' parameter specifies the list of priority of each backup point code for this Userpart. Allowable values are from 0 to 255.


	'''Note:''' Zero being the lowest priority.		'''Note:''' Zero being the lowest priority.


	----		----


	*The number concerned point code parameter specifies the number of concerned point code entries in the 'Concerned Point Code Entries' array		*The number concerned point code parameter specifies the number of concerned point code entries in the 'Concerned Point Code Entries' array
	*The array of concerned point code entries parameter (specifies the list of concerned point code for this Userpart		*The array of concerned point code entries parameter (specifies the list of concerned point code for this Userpart


	~~[[category:Needs revising]]~~

Toolpack:Create a SCCP userpart - Revision history

Allyntree at 17:14, 1 May 2018

Ktrueman: initial content