Toolpack:Configuring VoIP Interfaces E - Revision history

Allyntree at 16:36, 22 June 2024

2024-06-22T16:36:36Z

← Older revision		Revision as of 12:36, 22 June 2024
Line 8:		Line 8:
	\|-		\|-
	\|SBC		\|SBC
	\|3.0, 3.1		\|3.1, 3.3
	\|}		\|}

Allyntree at 13:36, 15 December 2020

2020-12-15T13:36:25Z

← Older revision		Revision as of 09:36, 15 December 2020
Line 1:		Line 1:
	~~=== '''''Applies to version(s): v3.0, v3.1''''' ===~~
	{{DISPLAYTITLE:Configuring VoIP Interfaces}}		{{DISPLAYTITLE:Configuring VoIP Interfaces}}

			{\| class="wikitable"
			\|-
			\|rowspan="2"\|This article applies to:
			\|'''Product'''
			\|'''Version'''
			\|-
			\|SBC
			\|3.0, 3.1
			\|}

	The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following:		The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following:

Allyntree at 17:38, 24 April 2019

2019-04-24T17:38:38Z

← Older revision		Revision as of 13:38, 24 April 2019
Line 1:		Line 1:
	=== '''''Applies to version(s): v3.0''''' ===		=== '''''Applies to version(s): v3.0, v3.1''''' ===
	{{DISPLAYTITLE:Configuring VoIP Interfaces}}		{{DISPLAYTITLE:Configuring VoIP Interfaces}}

Allyntree: /* To configure a VoIP0 or VoIP1 port */

2017-10-24T18:05:20Z

To configure a VoIP0 or VoIP1 port

← Older revision		Revision as of 14:05, 24 October 2017
Line 46:		Line 46:

	5. Activate the configuration		5. Activate the configuration
			*Select '''System''' from the navigation panel.
			*Click '''Activate'''

	~~Systems -> Edit -> Activate~~

			6. You must reboot the adapters only if you are using the vlan from ports 3441 to 3450.
			*Status -> Adapters -> Click on the adapter Serial Number -> Reboot adapter
	6. ~~It is necessary to~~ reboot the adapters if you are using the vlan from 3441 to 3450 ~~only~~.

	Status -> Adapters -> Click on the adapter Serial Number -> Reboot adapter

	It will take about 1.5 minutes to restart the unit.		It will take about 1.5 minutes to restart the unit.

	~~'''Note:''' in a 1+1 system, both units must be restarted.~~

	== List of Parameters ==		== List of Parameters ==

Allyntree: added screenshots

2017-10-24T17:59:30Z

added screenshots

← Older revision		Revision as of 13:59, 24 October 2017
Line 14:		Line 14:
	1. Select '''IP Interfaces''' from the navigation panel:		1. Select '''IP Interfaces''' from the navigation panel:

	[[~~New image needed - under Hardware Units~~]]		[[Image:CreateIpInterface_Tsbc_1.png]]

	<br> 2. Click the '''IP Interfaces''' tab.		<br> 2. Click the '''IP Interfaces''' tab.
Line 34:		Line 34:
	'''Note:''' IP addresses using different virtual ports must be on different subnets. <br>		'''Note:''' IP addresses using different virtual ports must be on different subnets. <br>

	[[~~New image needed~~]]		[[Image:CreateIpInterface_Tsbc_1a.png]]

	<br>		<br>
Line 40:		Line 40:
	4. The changes are displayed in the IP interfaces information panel:		4. The changes are displayed in the IP interfaces information panel:

	[[~~New image needed~~]]		[[Image:CreateIpInterface_Tsbc_1b.png]]


Line 58:		Line 58:

	'''Note:''' in a 1+1 system, both units must be restarted.		'''Note:''' in a 1+1 system, both units must be restarted.



	== List of Parameters ==		== List of Parameters ==

Manon Bélanger: Fix comment

2017-04-25T12:49:14Z

Fix comment

← Older revision		Revision as of 08:49, 25 April 2017
Line 32:		Line 32:
	*Click '''Save'''		*Click '''Save'''

	'''Note:''' ~~The~~ IP addresses ~~of ETH0, ETH1, VOIP0 and VOIP1~~ must be on different subnets. <br>		'''Note:''' IP addresses using different virtual ports must be on different subnets. <br>

	[[New image needed]]		[[New image needed]]

Manon Bélanger: First version

2017-04-20T13:38:50Z

First version

New page

=== '''''Applies to version(s): v3.0''''' ===
{{DISPLAYTITLE:Configuring VoIP Interfaces}}

The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following:

*IP Address
*Netmask
*Gateway

 

== To configure a VoIP0 or VoIP1 port ==

1. Select '''IP Interfaces''' from the navigation panel:

[[New image needed - under Hardware Units]]

 2. Click the '''IP Interfaces''' tab.
*Click '''Create New IP Interface'''

[[Image:Voip_Interface_1a.png]]

 3. Configure the IP port:

*Enter a name for the interface
*Select a service to use for the IP inteface
*Select a '''Virtual port''' from which IP packets will exit.
*Indicate whether or not to use DHCP to automatically get an IP address for this port. (selecting this option removes the need to enter and IP address, Netmask, and Gateway)
*Enter an '''IP address'''
*Enter a '''Netmask'''
*Enter a '''gateway address'''
*Click '''Save'''

'''Note:''' The IP addresses of ETH0, ETH1, VOIP0 and VOIP1 must be on different subnets. 

[[New image needed]]

 

4. The changes are displayed in the IP interfaces information panel:

[[New image needed]]

 

5. Activate the configuration

Systems -> Edit -> Activate

6. It is necessary to reboot the adapters if you are using the vlan from 3441 to 3450 only.

Status -> Adapters -> Click on the adapter Serial Number -> Reboot adapter

It will take about 1.5 minutes to restart the unit.

'''Note:''' in a 1+1 system, both units must be restarted.

== List of Parameters ==

*[[Parameter: Interface name|Interface name]]
*[[Parameter: Services to use|Services to use]]
*[[Parameter: Virtual port|Virtual port]]
*[[Parameter: Use DHCP|Use dynamic IP]]
*[[Parameter: IP Address|IP Address]]
*[[Parameter: Netmask|Netmask]]
*[[Parameter: Gateway|Gateway]]