Toolpack:Adding an TMS A - Revision history

Allyntree: /* Applies to version v2.6 */

2012-10-25T18:59:33Z

Applies to version v2.6

← Older revision		Revision as of 14:59, 25 October 2012
Line 33:		Line 33:


	[[Image:~~CreateHardwareTms_2_A~~.png]]		[[Image:CreateHardwareTms_2_1_A.png]]

Cbilodeau: remove TDM line type for TMS

2012-10-22T18:45:17Z

remove TDM line type for TMS

← Older revision		Revision as of 14:45, 22 October 2012
Line 27:		Line 27:
	* Enter the '''serial number''' of the new hardware device (filling in the Serial Number field will cause auto-completion of the field to occur).		* Enter the '''serial number''' of the new hardware device (filling in the Serial Number field will cause auto-completion of the field to occur).
	* Select the appropriate '''hardware device''' from the Type field. (In this case select TMS)		* Select the appropriate '''hardware device''' from the Type field. (In this case select TMS)
	* Select the type of TDM lines that the hardware device will support.
	* Enter the location in which the hardware device is installed.		* Enter the location in which the hardware device is installed.
	* Enter a meaningful description as to the usage or purpose of the hardware device.		* Enter a meaningful description as to the usage or purpose of the hardware device.

Allyntree: This is for the addition of a TMS. It differs slightly from adding a TMP.

2012-10-21T16:04:05Z

This is for the addition of a TMS. It differs slightly from adding a TMP.

← Older revision		Revision as of 12:04, 21 October 2012
Line 1:		Line 1:
	=== '''''Applies to version v2.6''''' ===		=== '''''Applies to version v2.6''''' ===
	{{DISPLAYTITLE:Adding a TMS ~~Adapter~~}}		{{DISPLAYTITLE:Adding TMS Hardware}}

	When you receive a new system, at least one hardware configuration will have been set in the [[Toolpack]] application server, by default. To add ~~other~~ hardware ~~devices~~, you must use the Tmedia [[Web Portal]].		When you receive a new system, at least one hardware configuration will have been set in the [[Toolpack]] application server, by default. To add a TMS hardware device to your system, you must use the Tmedia [[Web Portal]].

	[[Image:Schematic-pair-of-tmp6400s.jpg\|thumb\|250px\|Schematic showing 2 TMP6400 devices with an external server and a second machine with a web browser]]		[[Image:Schematic-pair-of-tmp6400s.jpg\|thumb\|250px\|Schematic showing 2 TMP6400 devices with an external server and a second machine with a web browser]]
Line 14:		Line 14:


	[[Image:~~CreateHardwareTmp_0_A~~.png]]		[[Image:CreateHardwareTms_0_A.png]]


Line 20:		Line 20:


	[[Image:~~CreateHardwareTmp_1_A~~.png]]		[[Image:CreateHardwareTms_1_A.png]]


Line 26:		Line 26:

	* Enter the '''serial number''' of the new hardware device (filling in the Serial Number field will cause auto-completion of the field to occur).		* Enter the '''serial number''' of the new hardware device (filling in the Serial Number field will cause auto-completion of the field to occur).
	* Select the appropriate '''hardware device''' from the Type field. (In this case select ~~TMP~~)		* Select the appropriate '''hardware device''' from the Type field. (In this case select TMS)
	* Select the type of TDM lines that the hardware device will support.		* Select the type of TDM lines that the hardware device will support.
	* Indicate if the device will operate as a backup in a 1+1 configuration.
	* Provide the amount of time is seconds, that the system will wait for calls to complete before shutting down for an upgrade.
	* Enter the location in which the hardware device is installed.		* Enter the location in which the hardware device is installed.
	* Enter a ~~meaningfful~~ description as to the usage or purpose of the hardware device.		* Enter a meaningful description as to the usage or purpose of the hardware device.
	* Select '''Enabled''' from the Target State field.		* Select '''Enabled''' from the Target State field.
	* Click '''Create'''		* Click '''Create'''


	[[Image:~~CreateHardwareTmp_2_A~~.png]]		[[Image:CreateHardwareTms_2_A.png]]


	4- Verify ~~that the '''"Adapter was successfully created"''' message appears, and~~ that the newly added hardware device appears in the '''Hardware List''' below		4- Verify that the newly added hardware device appears in the '''TMS Hardware List''' below


	[[Image:~~CreateHardwareTmp_3_A~~.png]]		[[Image:CreateHardwareTms_3_A.png]]

Allyntree: Created page with "=== '''''Applies to version v2.6''''' === {{DISPLAYTITLE:Adding a TMS Adapter}} When you receive a new system, at least one hardware configuration will have been set in the [..."

2012-10-21T15:52:21Z

Created page with "=== '''''Applies to version v2.6''''' === {{DISPLAYTITLE:Adding a TMS Adapter}} When you receive a new system, at least one hardware configuration will have been set in the [..."

New page

=== '''''Applies to version v2.6''''' ===
{{DISPLAYTITLE:Adding a TMS Adapter}}

When you receive a new system, at least one hardware configuration will have been set in the [[Toolpack]] application server, by default. To add other hardware devices, you must use the Tmedia [[Web Portal]].

[[Image:Schematic-pair-of-tmp6400s.jpg|thumb|250px|Schematic showing 2 TMP6400 devices with an external server and a second machine with a web browser]]

To add one or more additional hardware devices to the Toolpack system configuration, their serial numbers must be registered with the Toolpack application server.

'''To add a hardware device:'''

1- Click '''Hardware''' in the navigation panel

[[Image:CreateHardwareTmp_0_A.png]]

2- Click '''Create New Hardware''', to add a new hardware device

[[Image:CreateHardwareTmp_1_A.png]]

3- Enter a '''name''' for the hardware device

* Enter the '''serial number''' of the new hardware device (filling in the Serial Number field will cause auto-completion of the field to occur).
* Select the appropriate '''hardware device''' from the Type field. (In this case select TMP)
* Select the type of TDM lines that the hardware device will support.
* Indicate if the device will operate as a backup in a 1+1 configuration.
* Provide the amount of time is seconds, that the system will wait for calls to complete before shutting down for an upgrade.
* Enter the location in which the hardware device is installed.
* Enter a meaningfful description as to the usage or purpose of the hardware device.
* Select '''Enabled''' from the Target State field.
* Click '''Create'''

[[Image:CreateHardwareTmp_2_A.png]]

4- Verify that the '''"Adapter was successfully created"''' message appears, and that the newly added hardware device appears in the '''Hardware List''' below

[[Image:CreateHardwareTmp_3_A.png]]