Toolpack:Adding an Adapter C - Revision history

Allyntree: Fix typo: Is -> In

2015-05-27T15:11:20Z

Fix typo: Is -> In

← Older revision		Revision as of 11:11, 27 May 2015
Line 29:		Line 29:
	* Select the type of TDM lines that the hardware device will support.		* Select the type of TDM lines that the hardware device will support.
	* Indicate if the device will operate as a backup in an N+1 configuration. If this is the first device being added, leave this field clear.		* Indicate if the device will operate as a backup in an N+1 configuration. If this is the first device being added, leave this field clear.
	* Provide the amount of time is seconds, that the system will wait for calls to complete before shutting down for an upgrade.		* Provide the amount of time in seconds, that the system will wait for calls to complete before shutting down for an upgrade.
	* Enter the location in which the hardware device is installed.		* Enter the location in which the hardware device is installed.
	* Enter a meaningful description as to the usage or purpose of the hardware device.		* Enter a meaningful description as to the usage or purpose of the hardware device.

Allyntree: /* Applies to version v2.7 */

2013-04-26T18:26:56Z

Applies to version v2.7

← Older revision		Revision as of 14:26, 26 April 2013
Line 28:		Line 28:
	* Select the appropriate '''hardware device''' from the Type field. (In this case select TMP)		* Select the appropriate '''hardware device''' from the Type field. (In this case select TMP)
	* Select the type of TDM lines that the hardware device will support.		* Select the type of TDM lines that the hardware device will support.
	* Indicate if the device will operate as a backup in ~~a 1~~+1 configuration. If this is the first device being added, leave this field clear.		* Indicate if the device will operate as a backup in an N+1 configuration. If this is the first device being added, leave this field clear.
	* Provide the amount of time is seconds, that the system will wait for calls to complete before shutting down for an upgrade.		* Provide the amount of time is seconds, that the system will wait for calls to complete before shutting down for an upgrade.
	* Enter the location in which the hardware device is installed.		* Enter the location in which the hardware device is installed.
Line 39:		Line 39:

	'''NOTE'''		'''NOTE'''
	The following image shows the 1+1 Backup field set. This is done for the addition a secondary ~~TMP~~ that will operate as the designated 1+1 backup in a 1+1 Group.		The following image shows the N+1 Backup field set. This is done for the addition of a secondary device that will operate as the designated 1+1 backup in a 1+1 Group.

	[[Image:Hardware_3.png]]		[[Image:Hardware_3.png]]

Allyntree: /* Applies to version v2.7 */

2013-04-26T18:12:19Z

Applies to version v2.7

← Older revision		Revision as of 14:12, 26 April 2013
Line 11:		Line 11:
	'''To add a hardware device:'''		'''To add a hardware device:'''

	1- Click '''Hardware''' in the navigation panel		1- Click '''Hardware Units''' in the navigation panel


Line 17:		Line 17:


	2- Click '''Create New ~~Hardware~~''', to add a new hardware device		2- Click '''Create New Units''', to add a new hardware device

Allyntree: /* Applies to version v2.7 */

2013-04-26T18:10:20Z

Applies to version v2.7

← Older revision		Revision as of 14:10, 26 April 2013
Line 41:		Line 41:
	The following image shows the 1+1 Backup field set. This is done for the addition a secondary TMP that will operate as the designated 1+1 backup in a 1+1 Group.		The following image shows the 1+1 Backup field set. This is done for the addition a secondary TMP that will operate as the designated 1+1 backup in a 1+1 Group.

	[[Image:~~CreateHardwareTmp_2_1_A~~.png]]		[[Image:Hardware_3.png]]

	4- Verify that the '''"Adapter was successfully created"''' message appears, and that the newly added hardware device appears in the '''Hardware List''' below		4- Verify that the '''"Adapter was successfully created"''' message appears, and that the newly added hardware device appears in the '''Hardware List''' below

Allyntree: Created page with "=== '''''Applies to version v2.7''''' === {{DISPLAYTITLE:Adding Telecom Hardware}} When you receive a new system, at least one hardware configuration will have been set in th..."

2013-04-26T18:07:53Z

Created page with "=== '''''Applies to version v2.7''''' === {{DISPLAYTITLE:Adding Telecom Hardware}} When you receive a new system, at least one hardware configuration will have been set in th..."

New page

=== '''''Applies to version v2.7''''' ===
{{DISPLAYTITLE:Adding Telecom Hardware}}

When you receive a new system, at least one hardware configuration will have been set in the [[Toolpack]] application server, by default. To add other hardware devices, you must use the Tmedia [[Web Portal]].

[[Image:Schematic-pair-of-tmp6400s.jpg|thumb|250px|Schematic showing 2 TMP6400 devices with an external server and a second machine with a web browser]]

To add one or more additional hardware devices to the Toolpack system configuration, their serial numbers must be registered with the Toolpack application server.

'''To add a hardware device:'''

1- Click '''Hardware''' in the navigation panel

[[Image:Hardware_0.png]]

2- Click '''Create New Hardware''', to add a new hardware device

[[Image:Hardware_1.png]]

3- Enter a '''name''' for the hardware device

* Enter the '''serial number''' of the new hardware device (filling in the Serial Number field will cause auto-completion of the field to occur).
* Select the appropriate '''hardware device''' from the Type field. (In this case select TMP)
* Select the type of TDM lines that the hardware device will support.
* Indicate if the device will operate as a backup in a 1+1 configuration. If this is the first device being added, leave this field clear.
* Provide the amount of time is seconds, that the system will wait for calls to complete before shutting down for an upgrade.
* Enter the location in which the hardware device is installed.
* Enter a meaningful description as to the usage or purpose of the hardware device.
* Select '''Enabled''' from the Target State field.
* Click '''Create'''

[[Image:Hardware_2.png]]

'''NOTE'''
The following image shows the 1+1 Backup field set. This is done for the addition a secondary TMP that will operate as the designated 1+1 backup in a 1+1 Group.

[[Image:CreateHardwareTmp_2_1_A.png]]

4- Verify that the '''"Adapter was successfully created"''' message appears, and that the newly added hardware device appears in the '''Hardware List''' below

[[Image:CreateHardwareTmp_3_A.png]]

==List of Parameters==

* [[Parameter: Name|Name]]
* [[Parameter: Serial|Serial]]
* [[Parameter: Adapter Type|Adapter Type]]
* [[Parameter: Graceful Upgrade Timeout|Graceful Upgrade Timeout]]
* [[Parameter: Location|Location]]
* [[Parameter: Description|Description]]
* [[Parameter: Target State|Target State]]