Parameter: Point Code - Revision history

Luc Morissette: Added redirect to Point_Code page

2014-10-01T17:51:04Z

Added redirect to Point_Code page

← Older revision		Revision as of 13:51, 1 October 2014
Line 1:		Line 1:
	~~The~~ [[~~Point Code]] parameter has a number of meanings, which vary depending on the context in which it appears.~~		#REDIRECT[[Point_Code]]

	~~==When Creating a Point Code==~~

	~~The Point Code parameter is used to define a point code by assigning it numerical values.~~

	~~Values for this parameter are chosen from a series of drop-down menus. The values shown in each menu depend on the [[Parameter: DPC Length\|DPC Length]] chosen previously.~~

	~~==When Configuring an MTP3 Route==~~

	~~The [[Point Code]] parameter is used to associate a peer SS7 [[SP]] ([[DPC]]) with the MTP3 route. Available point codes are chosen from a drop-down list.~~

	~~[[Category:Parameters~~]]

Sylvain Fontaine at 15:37, 11 May 2012

2012-05-11T15:37:49Z

← Older revision		Revision as of 11:37, 11 May 2012
Line 1:		Line 1:
	The ~~'''~~Point Code~~'''~~ parameter has a number of meanings, which vary depending on the context in which it appears.		The [[Point Code]] parameter has a number of meanings, which vary depending on the context in which it appears.


	==When Creating a Point Code==		==When Creating a Point Code==

	The Point Code parameter is used to define a point code by assigning it numerical values~~. Values for this parameter are chosen from a series of drop-down menus. The values shown in each menu depend on the [[Parameter: DPC Length\|DPC Length]] chosen previously~~.		The Point Code parameter is used to define a point code by assigning it numerical values.

			Values for this parameter are chosen from a series of drop-down menus. The values shown in each menu depend on the [[Parameter: DPC Length\|DPC Length]] chosen previously.

	==When Configuring an MTP3 Route==		==When Configuring an MTP3 Route==

	The Point Code parameter is used to associate a ~~point code~~ with the MTP3 route. Available point codes are chosen from a drop-down list.		The [[Point Code]] parameter is used to associate a peer SS7 [[SP]] ([[DPC]]) with the MTP3 route. Available point codes are chosen from a drop-down list.

	[[Category:Parameters]]		[[Category:Parameters]]

Allyntree at 16:48, 23 August 2010

2010-08-23T16:48:34Z

← Older revision		Revision as of 12:48, 23 August 2010
Line 10:		Line 10:

	The Point Code parameter is used to associate a point code with the MTP3 route. Available point codes are chosen from a drop-down list.		The Point Code parameter is used to associate a point code with the MTP3 route. Available point codes are chosen from a drop-down list.

			[[Category:Parameters]]

Allyntree at 19:16, 4 August 2010

2010-08-04T19:16:21Z

← Older revision		Revision as of 15:16, 4 August 2010
Line 1:		Line 1:
	The Point Code is used to define a point code by assigning it numerical values. Values for this parameter are chosen from a series of drop-down menus. The values shown in each menu depend on the [[Parameter: DPC Length\|DPC Length]] chosen previously.		The '''Point Code''' parameter has a number of meanings, which vary depending on the context in which it appears.


			==When Creating a Point Code==

			The Point Code parameter is used to define a point code by assigning it numerical values. Values for this parameter are chosen from a series of drop-down menus. The values shown in each menu depend on the [[Parameter: DPC Length\|DPC Length]] chosen previously.


			==When Configuring an MTP3 Route==

			The Point Code parameter is used to associate a point code with the MTP3 route. Available point codes are chosen from a drop-down list.

Allyntree: Created page with 'The Point Code is used to define a point code by assigning it numerical values. Values for this parameter are chosen from a series of drop-down menus. The values shown in each me…'

2010-08-04T16:11:38Z

Created page with 'The Point Code is used to define a point code by assigning it numerical values. Values for this parameter are chosen from a series of drop-down menus. The values shown in each me…'

New page

The Point Code is used to define a point code by assigning it numerical values. Values for this parameter are chosen from a series of drop-down menus. The values shown in each menu depend on the [[Parameter: DPC Length|DPC Length]] chosen previously.