High Availability:Hardware:Clocking - Revision history

Allyntree at 16:36, 15 March 2018

2018-03-15T16:36:15Z

Allyntree: /* Choosing Clock Reference */

2018-03-15T16:35:15Z

Choosing Clock Reference

← Older revision		Revision as of 12:35, 15 March 2018
Line 11:		Line 11:
	Always place the most reliable clock source at the top of the clock references list in the web portal. This will avoid unnecessary clock switch over. TelcoBridges recommend to synchronize the clock on the BITS port when available. If your system includes [[TMG7800\|7800 TMS]], it is recommended that you use the [[TMG7800\|7800 TMS]] [[BITS]] ports as clock sources.		Always place the most reliable clock source at the top of the clock references list in the web portal. This will avoid unnecessary clock switch over. TelcoBridges recommend to synchronize the clock on the BITS port when available. If your system includes [[TMG7800\|7800 TMS]], it is recommended that you use the [[TMG7800\|7800 TMS]] [[BITS]] ports as clock sources.

	When the system selects a clock, it will only use clock sources that are valid and that are available on an active device of the system. For example, in a system containing 2 [[7800 TMS]] ( one will be active, the other standby ) the clock sources on the standby [[TMG7800\|7800 TMS]] (BITS ports) will not be selected. In the figure below, the clock source #3 and #4 will not be selected as system clock unless the standby [[TMG7800\|7800 TMS]] becomes active.		When the system selects a clock, it will only use clock sources that are valid and that are available on an active device of the system. For example, in a system containing two [[TMG7800\|7800 TMS]] ( one will be active, the other standby ) the clock sources on the standby [[TMG7800\|7800 TMS]] (BITS ports) will not be selected. In the figure below, the clock source #3 and #4 will not be selected as system clock unless the standby [[TMG7800\|7800 TMS]] becomes active.

	== Clock Redundancy ==		== Clock Redundancy ==

Allyntree: fixing links

2018-03-15T16:34:06Z

fixing links

Allyntree: /* Clock Sources */

2018-03-15T16:31:48Z

Clock Sources

← Older revision		Revision as of 12:31, 15 March 2018
Line 3:		Line 3:
	== Clock Sources ==		== Clock Sources ==
	The Toolpack system can synchronize the system on 3 types of sources:		The Toolpack system can synchronize the system on 3 types of sources:
	*[[BITS\| BITS port]] (Available on [[TMG7800]] telecom units and [[TMG7800 telecom units~~\|TMG7800~~]] with DS3 or SONET/SDH mezzanine. Also available on the [[7800 TMS]])		*[[BITS\| BITS port]] (Available on [[TMG7800]] telecom units and [[TMG7800\|TMG7800 telecom units]] with DS3 or SONET/SDH mezzanine. Also available on the [[7800 TMS]])
	*[[Line_Service \| Line Service]]		*[[Line_Service \| Line Service]]
	*[[SONET/SDH_interfaces \| SONET/SDH interface]]		*[[SONET/SDH_interfaces \| SONET/SDH interface]]

Allyntree at 16:31, 15 March 2018

2018-03-15T16:31:01Z

← Older revision		Revision as of 12:31, 15 March 2018
Line 3:		Line 3:
	== Clock Sources ==		== Clock Sources ==
	The Toolpack system can synchronize the system on 3 types of sources:		The Toolpack system can synchronize the system on 3 types of sources:
	*[[BITS\| BITS port]] (Available on [[TMG7800]] telecom units and [[TMG7800 telecom units]] with DS3 or SONET/SDH mezzanine. Also available on the [[7800 TMS]])		*[[BITS\| BITS port]] (Available on [[TMG7800]] telecom units and [[TMG7800 telecom units\|TMG7800]] with DS3 or SONET/SDH mezzanine. Also available on the [[7800 TMS]])
	*[[Line_Service \| Line Service]]		*[[Line_Service \| Line Service]]
	*[[SONET/SDH_interfaces \| SONET/SDH interface]]		*[[SONET/SDH_interfaces \| SONET/SDH interface]]

Allyntree: Needs revising edit. Rplace TMP7900 with TMG7800. Replaced TMP6400 with TMG7800 telecom units

2018-03-15T16:30:04Z

Needs revising edit. Rplace TMP7900 with TMG7800. Replaced TMP6400 with TMG7800 telecom units

← Older revision		Revision as of 12:30, 15 March 2018
Line 1:		Line 1:
	The clock is a necessary component of a TDM network. Synchronizing your system on the right clock, allows it to ~~offer good sound quality~~.		The clock is a necessary component of a TDM network. Synchronizing your system on the right clock, allows it to perform properly.

	== Clock Sources ==		== Clock Sources ==
	The Toolpack system can ~~synchronized~~ the system on 3 types of sources:		The Toolpack system can synchronize the system on 3 types of sources:
	*[[BITS\| BITS port]] (Available on [[~~TMP7900~~]] telecom units and [[~~TMP6400~~]] with DS3 or SONET/SDH mezzanine. Also available on the [[~~TMP7900-~~TMS]])		*[[BITS\| BITS port]] (Available on [[TMG7800]] telecom units and [[TMG7800 telecom units]] with DS3 or SONET/SDH mezzanine. Also available on the [[7800 TMS]])
	*[[Line_Service \| Line Service]]		*[[Line_Service \| Line Service]]
	*[[SONET/SDH_interfaces \| SONET/SDH interface]]		*[[SONET/SDH_interfaces \| SONET/SDH interface]]
Line 9:		Line 9:
	== Choosing Clock Reference ==		== Choosing Clock Reference ==

	Always place the most reliable clock source at the top of the clock references list in the web portal. This will avoid unnecessary clock switch over. TelcoBridges recommend to synchronize the clock on the BITS port when available. If your system includes [[~~TMP7900-~~TMS]], it is recommended to use the [[~~TMP7900-~~TMS]] [[BITS]] ports as clock sources.		Always place the most reliable clock source at the top of the clock references list in the web portal. This will avoid unnecessary clock switch over. TelcoBridges recommend to synchronize the clock on the BITS port when available. If your system includes [[7800 TMS]], it is recommended that you use the [[7800 TMS]] [[BITS]] ports as clock sources.

	When the system selects a clock, it will only use clock sources that are valid and that ~~it is~~ available on an active device of the system. For example, in a system containing 2 [[~~TMP7900-~~TMS]] ( one will be active, the other standby ) the clock sources on the standby [[~~TMP7900-~~TMS]] (BITS ports) will not be selected. In the figure below the clock source #3 and #4 ~~won't~~ be selected as system clock unless the standby [[~~TMP7900-~~TMS]] becomes active.		When the system selects a clock, it will only use clock sources that are valid and that are available on an active device of the system. For example, in a system containing 2 [[7800 TMS]] ( one will be active, the other standby ) the clock sources on the standby [[7800 TMS]] (BITS ports) will not be selected. In the figure below, the clock source #3 and #4 will not be selected as system clock unless the standby [[7800 TMS]] becomes active.

	== Clock Redundancy ==		== Clock Redundancy ==

	The system clock is configured using the Toolpack web portal. Toolpack ~~allow~~ the system to have a system clock references list. Clock redundancy is accomplished by configuring at least 2 valid clock references in the system. The system will scan through the clock references list until it finds a valid one. If the active clock source becomes unavailable, the system will scan through the clock reference list again to ~~found~~ another valid clock source. Clock recovery, which means that the system will switch back to a more preferred clock source if it becomes available again, can be configured in TMS network.		The system clock is configured using the Toolpack web portal. Toolpack allows the system to have a system clock references list. Clock redundancy is accomplished by configuring at least 2 valid clock references in the system. The system will scan through the clock references list until it finds a valid one. If the active clock source becomes unavailable, the system will scan through the clock reference list again to find another valid clock source. Clock recovery, which means that the system will switch back to a more preferred clock source if it becomes available again, can be configured in TMS network.

	Another redundancy feature for the system clock is the 2 [[BITS]] ports ~~which~~ can be assigned to different clock source.		Another redundancy feature for the system clock are the 2 [[BITS]] ports that can be assigned to different clock source.

	=== <u>Recommended Setup</u> ===		=== <u>Recommended Setup</u> ===
	Here is an example of a system clock where 2 [[~~TMP7900-~~TMS]] and the system ~~has~~ selected ~~the~~ clock source #1 as system clock:		Here is an example of a system clock where 2 [[7800 TMS]] and the system have selected clock source #1 as system clock:

	[[Image:Clocking_Ha_TMS.png\|widthpx\| ]]		[[Image:Clocking_Ha_TMS.png\|widthpx\| ]]
Line 26:		Line 26:
	== References ==		== References ==

	'''NOTE:'''These references assume that your system is running at ~~least~~ on Toolpack v2.3. ~~For configuring~~ the system, please select the appropriate [[Web_Portal\| Toolpack Web Tutorial Guide]].		'''NOTE:'''These references assume that your system is running at the very minimum on Toolpack v2.3. To configure the system, please select the appropriate [[Web_Portal\| Toolpack Web Tutorial Guide]].

	~~[[category:Needs revising]]~~

Lucas Trottier at 16:39, 9 May 2016

2016-05-09T16:39:26Z

← Older revision		Revision as of 12:39, 9 May 2016
Line 27:		Line 27:

	'''NOTE:'''These references assume that your system is running at least on Toolpack v2.3. For configuring the system, please select the appropriate [[Web_Portal\| Toolpack Web Tutorial Guide]].		'''NOTE:'''These references assume that your system is running at least on Toolpack v2.3. For configuring the system, please select the appropriate [[Web_Portal\| Toolpack Web Tutorial Guide]].

			[[category:Needs revising]]

Cbilodeau: replace tmedia with tdev

2011-02-15T18:32:23Z

replace tmedia with tdev

← Older revision		Revision as of 14:32, 15 February 2011
Line 3:		Line 3:
	== Clock Sources ==		== Clock Sources ==
	The Toolpack system can synchronized the system on 3 types of sources:		The Toolpack system can synchronized the system on 3 types of sources:
	*[[~~BITS_Ports~~ \| BITS port]] (~~only available~~ on ~~TMS1600~~ and ~~TMPx~~ with DS3 or SONET/SDH mezzanine)		*[[BITS\| BITS port]] (Available on [[TMP7900]] telecom units and [[TMP6400]] with DS3 or SONET/SDH mezzanine. Also available on the [[TMP7900-TMS]])
	*[[Line_Service \| Line Service]]		*[[Line_Service \| Line Service]]
	*[[SONET/SDH_interfaces \| SONET/SDH interface]]		*[[SONET/SDH_interfaces \| SONET/SDH interface]]
Line 9:		Line 9:
	== Choosing Clock Reference ==		== Choosing Clock Reference ==

	Always place the most reliable clock source at the top of the clock references list. This will avoid unnecessary clock switch over. TelcoBridges recommend to synchronize the clock on the BITS port when available. If your system includes ~~TMS1600~~, it is recommended to use the ~~TMS1600~~ BITS ports as clock sources.		Always place the most reliable clock source at the top of the clock references list in the web portal. This will avoid unnecessary clock switch over. TelcoBridges recommend to synchronize the clock on the BITS port when available. If your system includes [[TMP7900-TMS]], it is recommended to use the [[TMP7900-TMS]] [[BITS]] ports as clock sources.

	When the system selects a clock, it will only use clock sources that are valid and that it is available on an active device of the system. For example, in a system containing 2 ~~TMS1600~~ ( one will be active the other standby ) the clock sources on the standby ~~TMS1600~~ (BITS ports) will not be ~~chosen~~. In the figure below the clock source #3 and #4 won't be selected as system clock unless the standby ~~TMS1600~~ becomes active.		When the system selects a clock, it will only use clock sources that are valid and that it is available on an active device of the system. For example, in a system containing 2 [[TMP7900-TMS]] ( one will be active, the other standby ) the clock sources on the standby [[TMP7900-TMS]] (BITS ports) will not be selected. In the figure below the clock source #3 and #4 won't be selected as system clock unless the standby [[TMP7900-TMS]] becomes active.

	== Clock Redundancy ==		== Clock Redundancy ==

	The system clock is ~~configurred~~ using the Toolpack web portal. Toolpack allow the system to have a system clock references list. Clock redundancy is accomplished by configuring at least 2 valid clock ~~reference~~ in the system. The system will scan through the clock references list until it finds a valid one. If the active clock source becomes unavailable, the system will scan through the clock reference list again to found another valid clock source. Clock recovery, which means that the system will switch back to a more preferred clock source if it becomes available again, can be configured in TMS network.		The system clock is configured using the Toolpack web portal. Toolpack allow the system to have a system clock references list. Clock redundancy is accomplished by configuring at least 2 valid clock references in the system. The system will scan through the clock references list until it finds a valid one. If the active clock source becomes unavailable, the system will scan through the clock reference list again to found another valid clock source. Clock recovery, which means that the system will switch back to a more preferred clock source if it becomes available again, can be configured in TMS network.

	Another redundancy feature for the system clock is the 2 BITS ports which can be assigned to different clock source.		Another redundancy feature for the system clock is the 2 [[BITS]] ports which can be assigned to different clock source.

	=== <u>Recommended Setup</u> ===		=== <u>Recommended Setup</u> ===
	Here is an example of a system clock where 2 ~~TMS1600~~ and the system has selected the clock source #1 as system clock:		Here is an example of a system clock where 2 [[TMP7900-TMS]] and the system has selected the clock source #1 as system clock:

	[[Image:Clocking_Ha_TMS.png\|widthpx\| ]]		[[Image:Clocking_Ha_TMS.png\|widthpx\| ]]
Line 26:		Line 26:
	== References ==		== References ==

	'''NOTE:'''These ~~refences assumes~~ that your system is running Toolpack v2.3, ~~if your system is running another version of Toolpack~~ please select the appropriate [[Web_Portal\| Toolpack Web Tutorial Guide]].		'''NOTE:'''These references assume that your system is running at least on Toolpack v2.3. For configuring the system, please select the appropriate [[Web_Portal\| Toolpack Web Tutorial Guide]].

	*[[Toolpack_v2.3:Creating_BITS_Ports_as_a_Clocking_Source\|Configuring BITS ports]]
	*[[Toolpack_v2.3:Creating_a_Clocking_Source\|Configuring system clock references list]]
	*[[Toolpack_v2.3:Configuring_a_TMS_Network_System\|Configuring TMS network system]]
	*[[Toolpack_v2.3:Creating_a_Clocking_Source#Verifying_Status\|Verifying system clock status]]

Allyntree: /* References */

2010-05-23T18:04:57Z

References

← Older revision		Revision as of 14:04, 23 May 2010
Line 26:		Line 26:
	== References ==		== References ==

	'''NOTE:'''These refences assumes that your system is running Toolpack v2.3, if your system is running another version of Toolpack please select the appropriate [[~~Web_Portal_Tutorial_Guide_Versions~~ \| Toolpack Web Tutorial Guide]].		'''NOTE:'''These refences assumes that your system is running Toolpack v2.3, if your system is running another version of Toolpack please select the appropriate [[Web_Portal\| Toolpack Web Tutorial Guide]].

	*[[Toolpack_v2.3:Creating_BITS_Ports_as_a_Clocking_Source\|Configuring BITS ports]]		*[[Toolpack_v2.3:Creating_BITS_Ports_as_a_Clocking_Source\|Configuring BITS ports]]
	*[[Toolpack_v2.3:Creating_a_Clocking_Source\|Configuring system clock references list]]		*[[Toolpack_v2.3:Creating_a_Clocking_Source\|Configuring system clock references list]]
	*[[Toolpack_v2.3:Configuring_a_TMS_Network_System\|Configuring TMS network system]]		*[[Toolpack_v2.3:Configuring_a_TMS_Network_System\|Configuring TMS network system]]
	*[[Toolpack_v2.3:Creating_a_Clocking_Source#Verifying_Status\|Verifying system clock status]]		*[[Toolpack_v2.3:Creating_a_Clocking_Source#Verifying_Status\|Verifying system clock status]]

Cbilodeau: add precision for the clock selection scheme

2009-12-29T21:35:30Z

add precision for the clock selection scheme

← Older revision		Revision as of 17:35, 29 December 2009
Line 10:		Line 10:

	Always place the most reliable clock source at the top of the clock references list. This will avoid unnecessary clock switch over. TelcoBridges recommend to synchronize the clock on the BITS port when available. If your system includes TMS1600, it is recommended to use the TMS1600 BITS ports as clock sources.		Always place the most reliable clock source at the top of the clock references list. This will avoid unnecessary clock switch over. TelcoBridges recommend to synchronize the clock on the BITS port when available. If your system includes TMS1600, it is recommended to use the TMS1600 BITS ports as clock sources.

			When the system selects a clock, it will only use clock sources that are valid and that it is available on an active device of the system. For example, in a system containing 2 TMS1600 ( one will be active the other standby ) the clock sources on the standby TMS1600 (BITS ports) will not be chosen. In the figure below the clock source #3 and #4 won't be selected as system clock unless the standby TMS1600 becomes active.

	== Clock Redundancy ==		== Clock Redundancy ==
Line 18:		Line 20:

	=== <u>Recommended Setup</u> ===		=== <u>Recommended Setup</u> ===
	Here is an example of a system clock:		Here is an example of a system clock where 2 TMS1600 and the system has selected the clock source #1 as system clock:

	[[Image:Clocking_Ha_TMS.png\|widthpx\| ]]		[[Image:Clocking_Ha_TMS.png\|widthpx\| ]]

← Older revision		Revision as of 14:04, 23 May 2010
Line 26:		Line 26:
	== References ==		== References ==

	'''NOTE:'''These refences assumes that your system is running Toolpack v2.3, if your system is running another version of Toolpack please select the appropriate [[~~Web_Portal_Tutorial_Guide_Versions~~ \| Toolpack Web Tutorial Guide]].		'''NOTE:'''These refences assumes that your system is running Toolpack v2.3, if your system is running another version of Toolpack please select the appropriate [[Web_Portal\| Toolpack Web Tutorial Guide]].

	*[[Toolpack_v2.3:Creating_BITS_Ports_as_a_Clocking_Source\|Configuring BITS ports]]		*[[Toolpack_v2.3:Creating_BITS_Ports_as_a_Clocking_Source\|Configuring BITS ports]]
	*[[Toolpack_v2.3:Creating_a_Clocking_Source\|Configuring system clock references list]]		*[[Toolpack_v2.3:Creating_a_Clocking_Source\|Configuring system clock references list]]
	*[[Toolpack_v2.3:Configuring_a_TMS_Network_System\|Configuring TMS network system]]		*[[Toolpack_v2.3:Configuring_a_TMS_Network_System\|Configuring TMS network system]]
	*[[Toolpack_v2.3:Creating_a_Clocking_Source#Verifying_Status\|Verifying system clock status]]		*[[Toolpack_v2.3:Creating_a_Clocking_Source#Verifying_Status\|Verifying system clock status]]

← Older revision		Revision as of 12:36, 15 March 2018
Line 3:		Line 3:
	== Clock Sources ==		== Clock Sources ==
	The Toolpack system can synchronize the system on 3 types of sources:		The Toolpack system can synchronize the system on 3 types of sources:
	*~~[[BITS\|~~ BITS port]] (Available on [[TMG7800]] telecom units and [[TMG7800\|TMG7800 telecom units]] with DS3 or SONET/SDH mezzanine. Also available on the [[TMG7800\|7800 TMS]] )		*BITS port (Available on [[TMG7800]] telecom units and [[TMG7800\|TMG7800 telecom units]] with DS3 or SONET/SDH mezzanine. Also available on the [[TMG7800\|7800 TMS]] )
	*[[Line_Service \| Line Service]]		*[[Line_Service \| Line Service]]
	*[[SONET/SDH_interfaces \| SONET/SDH interface]]		*[[SONET/SDH_interfaces \| SONET/SDH interface]]
Line 9:		Line 9:
	== Choosing Clock Reference ==		== Choosing Clock Reference ==

	Always place the most reliable clock source at the top of the clock references list in the web portal. This will avoid unnecessary clock switch over. TelcoBridges recommend to synchronize the clock on the BITS port when available. If your system includes [[TMG7800\|7800 TMS]], it is recommended that you use the [[TMG7800\|7800 TMS]] [[BITS]] ports as clock sources.		Always place the most reliable clock source at the top of the clock references list in the web portal. This will avoid unnecessary clock switch over. TelcoBridges recommend to synchronize the clock on the BITS port when available. If your system includes [[TMG7800\|7800 TMS]], it is recommended that you use the [[TMG7800\|7800 TMS]] BITS ports as clock sources.

	When the system selects a clock, it will only use clock sources that are valid and that are available on an active device of the system. For example, in a system containing two [[TMG7800\|7800 TMS]] ( one will be active, the other standby ) the clock sources on the standby [[TMG7800\|7800 TMS]] (BITS ports) will not be selected. In the figure below, the clock source #3 and #4 will not be selected as system clock unless the standby [[TMG7800\|7800 TMS]] becomes active.		When the system selects a clock, it will only use clock sources that are valid and that are available on an active device of the system. For example, in a system containing two [[TMG7800\|7800 TMS]] ( one will be active, the other standby ) the clock sources on the standby [[TMG7800\|7800 TMS]] (BITS ports) will not be selected. In the figure below, the clock source #3 and #4 will not be selected as system clock unless the standby [[TMG7800\|7800 TMS]] becomes active.
Line 17:		Line 17:
	The system clock is configured using the Toolpack web portal. Toolpack allows the system to have a system clock references list. Clock redundancy is accomplished by configuring at least 2 valid clock references in the system. The system will scan through the clock references list until it finds a valid one. If the active clock source becomes unavailable, the system will scan through the clock reference list again to find another valid clock source. Clock recovery, which means that the system will switch back to a more preferred clock source if it becomes available again, can be configured in TMS network.		The system clock is configured using the Toolpack web portal. Toolpack allows the system to have a system clock references list. Clock redundancy is accomplished by configuring at least 2 valid clock references in the system. The system will scan through the clock references list until it finds a valid one. If the active clock source becomes unavailable, the system will scan through the clock reference list again to find another valid clock source. Clock recovery, which means that the system will switch back to a more preferred clock source if it becomes available again, can be configured in TMS network.

	Another redundancy feature for the system clock are the ~~2 [[~~BITS]] ports that can be assigned to different clock source.		Another redundancy feature for the system clock are the two BITS ports that can be assigned to different clock source.

	=== <u>Recommended Setup</u> ===		=== <u>Recommended Setup</u> ===

← Older revision		Revision as of 12:34, 15 March 2018
Line 3:		Line 3:
	== Clock Sources ==		== Clock Sources ==
	The Toolpack system can synchronize the system on 3 types of sources:		The Toolpack system can synchronize the system on 3 types of sources:
	*[[BITS\| BITS port]] (Available on [[TMG7800]] telecom units and [[TMG7800\|TMG7800 telecom units]] with DS3 or SONET/SDH mezzanine. Also available on the [[7800 TMS]])		*[[BITS\| BITS port]] (Available on [[TMG7800]] telecom units and [[TMG7800\|TMG7800 telecom units]] with DS3 or SONET/SDH mezzanine. Also available on the [[TMG7800\|7800 TMS]] )
	*[[Line_Service \| Line Service]]		*[[Line_Service \| Line Service]]
	*[[SONET/SDH_interfaces \| SONET/SDH interface]]		*[[SONET/SDH_interfaces \| SONET/SDH interface]]
Line 9:		Line 9:
	== Choosing Clock Reference ==		== Choosing Clock Reference ==

	Always place the most reliable clock source at the top of the clock references list in the web portal. This will avoid unnecessary clock switch over. TelcoBridges recommend to synchronize the clock on the BITS port when available. If your system includes [[7800 TMS]], it is recommended that you use the [[7800 TMS]] [[BITS]] ports as clock sources.		Always place the most reliable clock source at the top of the clock references list in the web portal. This will avoid unnecessary clock switch over. TelcoBridges recommend to synchronize the clock on the BITS port when available. If your system includes [[TMG7800\|7800 TMS]], it is recommended that you use the [[TMG7800\|7800 TMS]] [[BITS]] ports as clock sources.

	When the system selects a clock, it will only use clock sources that are valid and that are available on an active device of the system. For example, in a system containing 2 [[7800 TMS]] ( one will be active, the other standby ) the clock sources on the standby [[7800 TMS]] (BITS ports) will not be selected. In the figure below, the clock source #3 and #4 will not be selected as system clock unless the standby [[7800 TMS]] becomes active.		When the system selects a clock, it will only use clock sources that are valid and that are available on an active device of the system. For example, in a system containing 2 [[7800 TMS]] ( one will be active, the other standby ) the clock sources on the standby [[TMG7800\|7800 TMS]] (BITS ports) will not be selected. In the figure below, the clock source #3 and #4 will not be selected as system clock unless the standby [[TMG7800\|7800 TMS]] becomes active.

	== Clock Redundancy ==		== Clock Redundancy ==
Line 20:		Line 20:

	=== <u>Recommended Setup</u> ===		=== <u>Recommended Setup</u> ===
	Here is an example of a system clock where 2 [[7800 TMS]] and the system have selected clock source #1 as system clock:		Here is an example of a system clock where 2 [[TMG7800\|7800 TMS]] and the system have selected clock source #1 as system clock:

	[[Image:Clocking_Ha_TMS.png\|widthpx\| ]]		[[Image:Clocking_Ha_TMS.png\|widthpx\| ]]