Enabling Remote NAT Traversal A - Revision history

Allyntree at 14:08, 14 September 2022

2022-09-14T14:08:30Z

← Older revision		Revision as of 10:08, 14 September 2022
Line 1:		Line 1:
	~~=== '''''Applies to version: v2.7.''''' ===~~
	{{DISPLAYTITLE:Enabling Remote NAT Traversal}}		{{DISPLAYTITLE:Enabling Remote NAT Traversal}}
			{\| class="wikitable"
			\|-
			\|rowspan="2"\|This article applies to:
			\|'''Product'''
			\|'''Version'''
			\|-
			\|Tmedia
			\|2.7
			\|}

	<br>		<br>

Allyntree at 18:47, 12 July 2013

2013-07-12T18:47:31Z

← Older revision		Revision as of 14:47, 12 July 2013
Line 6:		Line 6:


	1- Select '''~~NAP~~''' from the navigation panel		1- Select '''NAPs''' from the navigation panel

	[[Image:~~NatTraversal_0_A~~.png]]		[[Image:Sip_C_0.png]]

Allyntree at 17:22, 21 May 2013

2013-05-21T17:22:54Z

← Older revision		Revision as of 13:22, 21 May 2013
Line 17:		Line 17:


	3- In the ~~section~~ '''Network Address Translation''':		3- In the '''Network Address Translation''' section:
	* Choose the proper Remote Method.		* Choose the proper Remote Method.
	~~[[Image:nat_remote.png]]~~


	[[Image:nat_remote_select.png]]		[[Image:nat_remote_select.png]]
Line 27:		Line 25:


	~~'''Here's more useful regarding the~~ 3 Remote NAT Traversal Methods:~~'''~~		The 3 Remote NAT Traversal Methods are described as follows:

	'''No NAT'''		'''No NAT'''

	~~When the~~ local endpoint is NOT behind a NAT. This means, your local endpoint has a Public IP address~~. Public means the IP address~~ is globally routable on the Internet. ~~If you're not sure~~, ~~you can~~ refer to http://en.wikipedia.org/wiki/Private_network.		The local endpoint is NOT behind a NAT. This means, your local endpoint has a Public IP address, which is globally routable on the Internet. For further information, refer to http://en.wikipedia.org/wiki/Private_network.

	'''Force Passive Mode'''		'''Force Passive Mode'''

	The TMG will NOT send any RTP ~~packet~~ and wait for the first RTP packet. The remote endpoint will send the first RTP packet. It will ignore the IP address/port sent in the SDP (in the SIP '200 OK' message)and use the IP address/port from where it received the RTP packet.		The TMG will NOT send any RTP packets and will wait for the first RTP packet. The remote endpoint will send the first RTP packet. It will ignore the IP address/port sent in the SDP (in the SIP '200 OK' message)and use the IP address/port from where it received the RTP packet.

	Note: If the remote endpoint is also set as passive, this method will not work~~, since~~ both ~~side~~ will wait for the first incoming RTP packet.		Note: If the remote endpoint is also set as passive, this method will not work because both sides will wait for the first incoming RTP packet.

	'''Parse Direction Attribute'''		'''Parse Direction Attribute'''

	TMG will look in the SDP to find an attribute direction:active. If it ~~find~~ this attribute, TMG will act exactly as the “Force Passive Mode” method. In fact, this a dynamic way to enable the “Force Passive Mode”.		The TMG will look in the SDP to find an attribute direction:active. If it finds this attribute, the TMG will act exactly as the “Force Passive Mode” method. In fact, this a dynamic way to enable the “Force Passive Mode”.

	== Related actions ==		== Related actions ==
	[[Symmetric_NAT_Traversal\|Symmetric NAT traversal]]		[[Symmetric_NAT_Traversal\|Symmetric NAT traversal]]

Clod Patry: adding the 3 local methods that we currently support.

2013-05-03T18:55:52Z

adding the 3 local methods that we currently support.

@@ Line 25: / Line 25: @@
 * Click '''Save'''
 == Related actions ==
 [[Symmetric_NAT_Traversal|Symmetric NAT traversal]]

Clod Patry at 18:53, 3 May 2013

2013-05-03T18:53:37Z

← Older revision		Revision as of 14:53, 3 May 2013
Line 17:		Line 17:


	3- ~~Click~~ '''~~NAT Traversal~~''' ~~to view options.~~		3- In the section '''Network Address Translation''':
	* ~~Set~~ the ~~'''Enable''' checkbox~~.		* Choose the proper Remote Method.
			[[Image:nat_remote.png]]


			[[Image:nat_remote_select.png]]

	* Click '''Save'''		* Click '''Save'''
	~~[[Image:NatTraversal_1_A.png]]~~

	== Related actions ==		== Related actions ==
	[[Symmetric_NAT_Traversal\|Symmetric NAT traversal]]		[[Symmetric_NAT_Traversal\|Symmetric NAT traversal]]

Clod Patry: Created page with "=== '''''Applies to version: v2.7.''''' === {{DISPLAYTITLE:Enabling Remote NAT Traversal}}
To enable Remote NAT Traversal: 1- Select '''NAP''' from the navigation pane..."

2013-05-03T18:49:48Z

Created page with "=== '''''Applies to version: v2.7.''''' === {{DISPLAYTITLE:Enabling Remote NAT Traversal}} <br> To enable Remote NAT Traversal: 1- Select '''NAP''' from the navigation pane..."

New page

=== '''''Applies to version: v2.7.''''' ===
{{DISPLAYTITLE:Enabling Remote NAT Traversal}}

<br>
To enable Remote NAT Traversal:

1- Select '''NAP''' from the navigation panel

[[Image:NatTraversal_0_A.png]]

2- Select a SIP NAP from the '''Network Access Point List'''
* Click '''Edit'''

[[Image:SipParams_0_1_A.png]]

3- Click '''NAT Traversal''' to view options.
* Set the '''Enable''' checkbox.
* Click '''Save'''
[[Image:NatTraversal_1_A.png]]

== Related actions ==
[[Symmetric_NAT_Traversal|Symmetric NAT traversal]]