Configure Fax Passthrough NSE A - Revision history

Allyntree at 14:55, 9 September 2022

2022-09-09T14:55:37Z

← Older revision		Revision as of 10:55, 9 September 2022
Line 1:		Line 1:
	~~=== '''''Applies to version(s): v2.7.''''' ===~~
	{{DISPLAYTITLE:Configure Fax Passthrough NSE}}		{{DISPLAYTITLE:Configure Fax Passthrough NSE}}
			{\| class="wikitable"
			\|-
			\|rowspan="2"\|This article applies to:
			\|'''Product'''
			\|'''Version'''
			\|-
			\|Tmedia
			\|2.7
			\|}

	To enable passthrough with NSE, follow these steps:		To enable passthrough with NSE, follow these steps:

Clod Patry: adding header

2012-06-18T14:06:10Z

adding header

← Older revision		Revision as of 10:06, 18 June 2012
Line 1:		Line 1:
			=== '''''Applies to version(s): v2.7.''''' ===
			{{DISPLAYTITLE:Configure Fax Passthrough NSE}}

	To enable passthrough with NSE, follow these steps:		To enable passthrough with NSE, follow these steps:
	<pre>		<pre>

Clod Patry: Adding the screen-shot

2012-06-15T17:53:57Z

Adding the screen-shot

← Older revision		Revision as of 13:53, 15 June 2012
Line 8:		Line 8:
	6. Make sure "Use NSE" is checked. By unchecking this option, you will switch to Fax Passthrough using SIP re-INVITE.		6. Make sure "Use NSE" is checked. By unchecking this option, you will switch to Fax Passthrough using SIP re-INVITE.
	</pre>		</pre>


			[[Image:profile_nse_v27.png]]

Clod Patry: remove the condition with CNG for NSE

2012-06-15T17:50:36Z

remove the condition with CNG for NSE

← Older revision		Revision as of 13:50, 15 June 2012
Line 4:		Line 4:
	2. Make sure "Detection Mode" is Standard.		2. Make sure "Detection Mode" is Standard.
	3. Make sure "Relay Mode" is Passthrough.		3. Make sure "Relay Mode" is Passthrough.
	4~~. Make sure "Enable switching to FAX relay upon CNG tone" is checked.~~		4. Make sure "Detection type" is "Silence Suppression off"
	5. Make sure "Detection type" is "Silence Suppression off"		5. Make sure the Codec is the same as the remote end.
	6. Make sure the Codec is the same as the remote end.		6. Make sure "Use NSE" is checked. By unchecking this option, you will switch to Fax Passthrough using SIP re-INVITE.
	7. Make sure "Use NSE" is checked. By unchecking this option, you will switch to Fax Passthrough using SIP re-INVITE.
	</pre>		</pre>

Clod Patry: create page passhtru with NSE

2012-06-15T17:46:43Z

create page passhtru with NSE

New page

To enable passthrough with NSE, follow these steps:
<pre>
1. Make sure "Enable Fax/Modem Relay" is enabled.
2. Make sure "Detection Mode" is Standard.
3. Make sure "Relay Mode" is Passthrough.
4. Make sure "Enable switching to FAX relay upon CNG tone" is checked.
5. Make sure "Detection type" is "Silence Suppression off"
6. Make sure the Codec is the same as the remote end.
7. Make sure "Use NSE" is checked. By unchecking this option, you will switch to Fax Passthrough using SIP re-INVITE.
</pre>