Configure Fax Passthrough D - Revision history

Allyntree at 14:54, 9 September 2022

2022-09-09T14:54:47Z

← Older revision		Revision as of 10:54, 9 September 2022
Line 31:		Line 31:
	* Check the '''Switch to FAX relay upon CNG tone''' option.		* Check the '''Switch to FAX relay upon CNG tone''' option.
	* Set '''Detection type''' to "Silence Suppression off"		* Set '''Detection type''' to "Silence Suppression off"
	* Verify ~~the~~ the Codec is the same as the remote end.		* Verify the Codec is the same as the remote end.
	* Click '''Create'''		* Click '''Create'''

Allyntree at 14:52, 9 September 2022

2022-09-09T14:52:33Z

← Older revision		Revision as of 10:52, 9 September 2022
Line 1:		Line 1:
	~~=== '''''Applies to version(s): v2.8.''''' ===~~
	{{DISPLAYTITLE:Configure Fax Passthrough}}		{{DISPLAYTITLE:Configure Fax Passthrough}}
			{\| class="wikitable"
			\|-
			\|rowspan="2"\|This article applies to:
			\|'''Product'''
			\|'''Version'''
			\|-
			\|Tmedia
			\|2.8
			\|}

	'''To enable passthrough:'''		'''To enable passthrough:'''
Line 29:		Line 37:


	5. Verify ~~thet~~ the '''Profile was successfully created''' message is displayed.		5. Verify that the '''Profile was successfully created''' message is displayed.

	[[Image:ConfigureFaxPassthrough_4.png]]		[[Image:ConfigureFaxPassthrough_4.png]]

Allyntree at 15:52, 7 October 2014

2014-10-07T15:52:33Z

← Older revision		Revision as of 11:52, 7 October 2014
Line 10:		Line 10:

	2. Click '''Create New Profile'''		2. Click '''Create New Profile'''

	[[Image:ConfigureFaxPassthrough_1.png]]		[[Image:ConfigureFaxPassthrough_1.png]]

Allyntree: new 2.8 article

2014-10-07T15:52:21Z

new 2.8 article

← Older revision		Revision as of 11:52, 7 October 2014
Line 9:		Line 9:


	2. ~~Set~~ '''~~Detection Mode~~''' ~~to Standard~~.		2. Click '''Create New Profile'''
			[[Image:ConfigureFaxPassthrough_1.png]]

	3. ~~Set~~ '''Relay ~~Mode~~''' to ~~Passthrough~~.		3. Enter a name for the Fax Profile.
			* Click '''Fax/Modem Relay''' to expand the view.

	~~4. Check the '''Switch to FAX relay upon CNG tone''' option~~.		[[Image:ConfigureFaxPassthrough_2.png]]

	5. Set '''Detection type''' to "Silence Suppression off"		4. Configure the settings:
			* Set '''Detection Mode''' to Standard.
			* Set '''Relay Mode''' to Passthrough.
			* Check the '''Switch to FAX relay upon CNG tone''' option.
			* Set '''Detection type''' to "Silence Suppression off"
			* Verify the the Codec is the same as the remote end.
			* Click '''Create'''

	~~6. Verify the the Codec is the same as the remote end~~.		[[Image:ConfigureFaxPassthrough_3.png]]


	[[Image:~~ConfigureFaxPassthrough_1~~.png]]		5. Verify thet the '''Profile was successfully created''' message is displayed.

			[[Image:ConfigureFaxPassthrough_4.png]]

Allyntree: new 2.8 article

2014-10-07T15:38:18Z

new 2.8 article

New page

=== '''''Applies to version(s): v2.8.''''' ===
{{DISPLAYTITLE:Configure Fax Passthrough}}

'''To enable passthrough:'''

1. Select '''Profiles''' from the navigation menu.

[[Image:ConfigureFaxPassthrough_0.png]]

2. Set '''Detection Mode''' to Standard.

3. Set '''Relay Mode''' to Passthrough.

4. Check the '''Switch to FAX relay upon CNG tone''' option.

5. Set '''Detection type''' to "Silence Suppression off"

6. Verify the the Codec is the same as the remote end.

[[Image:ConfigureFaxPassthrough_1.png]]