CAS R1 E&M - Revision history

Luc Morissette at 14:52, 17 January 2023

2023-01-17T14:52:03Z

← Older revision		Revision as of 10:52, 17 January 2023
Line 75:		Line 75:
	},		},
	</pre>		</pre>
	See [[CASr1_scripting#MFR1_mapping\|CAS MFR1 Mapping]] to know valid values.		See [[CASr1_scripting#MFR1_mapping\|CAS MFR1 Mapping]] to know valid prefix and suffix values.
	<br>		<br>
	<br>		<br>

Luc Morissette: /* Detection of ANI and/or DNIS */

2023-01-17T14:37:15Z

Detection of ANI and/or DNIS

← Older revision		Revision as of 10:37, 17 January 2023
Line 75:		Line 75:
	},		},
	</pre>		</pre>
			See [[CASr1_scripting#MFR1_mapping\|CAS MFR1 Mapping]] to know valid values.
			<br>
			<br>
	Please read detailed information about configuration of ANI/DNIS reception and transmission using the variables above:		Please read detailed information about configuration of ANI/DNIS reception and transmission using the variables above:
	* [[CASr1_scripting#ACTION_SEND_ANI\|Options for sending ANI]]		* [[CASr1_scripting#ACTION_SEND_ANI\|Options for sending ANI]]

Allyntree at 14:03, 7 September 2022

2022-09-07T14:03:20Z

← Older revision		Revision as of 10:03, 7 September 2022
Line 1:		Line 1:
			{{DISPLAYTITLE:CAS R1 E&M}}
	E&M ~~"Wink Start" is a CASr1 variant.~~

	== Overview ==		== Overview ==

	The E&M (often called "Wink Start") variants of CASR1 are "~~symetrical~~" CASR1 variants (both sides use identical signaling and state machines, calls can be made in both directions).		The E&M (often called "Wink Start") variants of CASR1 are "symmetrical" CASR1 variants (both sides use identical signaling and state machines, and calls can be made in both directions).
	* Only bit A is used (generally replicated to bit B)		* Only bit A is used (generally replicated to bit B)
	** Idle ("on hook") pattern is to set bit A to 0		** Idle ("on hook") pattern is to set bit A to 0
Line 15:		Line 14:
	* Receiver side receives digit (sends another "wink" in "Wink-start-ack" variant)		* Receiver side receives digit (sends another "wink" in "Wink-start-ack" variant)
	* Receiver side eventually goes "off hook"		* Receiver side eventually goes "off hook"

	Call termination:		Call termination:
	* One side goes "on hook"		* One side goes "on hook"
Line 42:		Line 42:
	</pre>		</pre>

	Depending if you want to use 0, 1 or 2 winks.		Depending upon whether you want to use 0, 1 or 2 winks.

	=== Choosing tone type ===		=== Choosing tone type ===

Abrassard at 20:40, 22 November 2013

2013-11-22T20:40:33Z

← Older revision		Revision as of 16:40, 22 November 2013
Line 56:		Line 56:
	* DNIS stands for "Dialed Number Identification Service" (or "called number").		* DNIS stands for "Dialed Number Identification Service" (or "called number").

	In the E&M variants, ANI (calling number) is optional, while DNIS (called number) is mandatory.		In the E&M variants, ANI (calling number) is optional, while DNIS (called number) is most of the time mandatory (though in some cases may be omitted).

	==== Detection of ANI and/or DNIS ====		==== Detection of ANI and/or DNIS ====
Line 82:		Line 82:

	==== Enabling/disabling usage of ANI ====		==== Enabling/disabling usage of ANI ====
	To enable detection of ANI, enable one of the 3 detection methods above (prefix/suffix, expected number of digits, or inter-digit timeout).		To enable detection of ANI, enable one of the 3 detection methods above in the "ANI" configuration (prefix/suffix, expected number of digits, or inter-digit timeout).

	If none is used, ANI won't be sent or received by the script.		If none is used, ANI won't be sent or received by the script.

			==== Enabling/disabling usage of DNIS ====
			To enable detection of DNIS, enable one of the 3 detection methods above in the "DNIS" configuration (prefix/suffix, expected number of digits, or inter-digit timeout).

			If none is used, DNIS won't be sent or received by the script.
			Instead of a called number, the default E&M script will store the trunk number and timeslot number, separated by digit 'A'.
			Format will be like 01A22 (meaning trunk number 1, timeslot 22)

Abrassard at 15:43, 8 August 2013

2013-08-08T15:43:29Z

← Older revision		Revision as of 11:43, 8 August 2013
Line 44:		Line 44:
	Depending if you want to use 0, 1 or 2 winks.		Depending if you want to use 0, 1 or 2 winks.

			=== Choosing tone type ===
			With CAS R1, ANI/DNIS can be sent using either DTMF or MFR1 tones.

			To specify the type of tones to use, use the following constant:
			<pre>
			TONE_USE_DTMF = 1
			</pre>

	=== Configuring exchange of ANI/DNIS ===		=== Configuring exchange of ANI/DNIS ===
Line 65:		Line 72:
	suffix = "#",		suffix = "#",
	expected_digits = 0,		expected_digits = 0,
	inter_digit_timeout = 0,		inter_digit_timeout = 5000,
	},		},
	</pre>		</pre>

	* ANI/DNIS ~~may be surrounded by separator digits (most of the time "KP"~~ and ~~"ST" MFR1 tones).~~
	** Prefix/suffix are automatically added by the script when the ~~digits are being sent~~		Please read detailed information about configuration of ANI/DNIS reception and transmission using the variables above:
	** Prefix/suffix are detected by the script and removed from the collected digits before being reported to the application as calling/called numbers		* [[CASr1_scripting#ACTION_SEND_ANI\|Options for sending ANI]]
	* ~~Expected number of digits is generally used in cases where no prefix/suffix are used, but instead a well-known (and fixed) number of digits are expected to be received~~		* [[CASr1_scripting#ACTION_WAIT_ANI\|Options for receiving ANI]]
	* The inter-digit timeout allows to declare ANI~~/DNIS complete after a delay without receiving subsequent digits. This is generally used with prefix/suffix separators are not used.~~

	==== Enabling/disabling usage of ANI ====		==== Enabling/disabling usage of ANI ====

Abrassard: moved E&M to CAS R1 E&M: Missing "CAS" in the title, "E&M" is too short!

2013-08-08T15:15:32Z

moved E&M to CAS R1 E&M: Missing "CAS" in the title, "E&M" is too short!

← Older revision	Revision as of 11:15, 8 August 2013
(No difference)

Abrassard: Improved doc

2013-08-05T17:23:32Z

Improved doc

Show changes

Clod Patry: basic page for E&M

2013-07-31T19:45:02Z

basic page for E&M

← Older revision		Revision as of 15:45, 31 July 2013
Line 1:		Line 1:
	~~#REDIRECT~~ [[CASr1 scripting]]
			E&M is a CASr1 family.
			This script is used to configure the following variants:
			* Immediate delay
			* Wink-start
			* Double-ack
			* EANA

			== Overview ==
			E&M scripts use the same logic specified in [[CASr1 scripting]].


			== Configuration ==
			To specify a script to use E&M, you MUST specify one of the following:
			<pre>
			CasR1.Variant = CasR1.VariantTypes.DELAY_START
			CasR1.Variant = CasR1.VariantTypes.WINK_START
			CasR1.Variant = CasR1.VariantTypes.WINK_START_ACK
			CasR1.Variant = CasR1.VariantTypes.EANA
			</pre>

			Depending if you want to use 0, 1 or 2 winks and if you plan to receive or not the ANI.



			== Subvariants ==
			Here are the differences between the subvariants:

			=== Delay Start ===
			there's no wink before receiving ANI/DNIS.

			=== Wink Start ===
			There's 1 wink before receiving ANI/DNIS.

			=== Wink Start ACK ===
			There's 1 wink before receiving ANI/DNIS.
			There's 1 wink after receiving ANI/DNIS.

			=== EANA ===
			This variant is similar to wink start, but it contains ANI, while wink-start has no ANI.


			== ANI ==

			This is the Automic Number Identification, commonly called the "calling number".

			<pre>
			ANI = {
			prefix = "*",
			suffix = "*",
			expected_digits = 0,
			inter_digit_timeout = 0,
			}
			</pre>


			== DNIS ==

			This is the Dialed Number Identification Service, commonly called the "called number".
			<pre>
			DNIS = {
			prefix = "*",
			suffix = "#",
			expected_digits = 0,
			inter_digit_timeout = 0,
			}
			</pre>

			By using the 2 above sections, you're expecting to receive:
			<pre>
			ANIDNIS#
			</pre>
			when you're in the incoming addressing state.

Clod Patry: moved E&M to CASr1 scripting: this page is what's needed for all CASr1 script, not specific to E&M.

2013-07-31T19:11:36Z

moved E&M to CASr1 scripting: this page is what's needed for all CASr1 script, not specific to E&M.

New page

#REDIRECT [[CASr1 scripting]]