Actions

Toolpack:Creating an SCCP Route A: Difference between revisions

m (typo)
 
(12 intermediate revisions by 2 users not shown)
Line 1: Line 1:
Now that you have created an [[SCCP]] LSAP, you must create a new [[Toolpack:Create_an_SCCP_Route|SCCP route]] for your system.
=== '''''Applies to version(s): v2.5, v2.6, v2.7''''' ===
{{DISPLAYTITLE:Creating an SCCP Route}}
Now that you have created an [[SCCP]] [[LSAP]], you must create a new [[Toolpack:Create_an_SCCP_Route|SCCP route]] for your system.
This step in the Web Portal configuration exists to create a route to a specific destination point code (DPC).  
This step in the Web Portal configuration exists to create a route to a specific destination point code (DPC).  


Line 11: Line 13:
2- Configure the new SCCP Route:
2- Configure the new SCCP Route:


* Choose a '''name''' for the new route
* Choose a [[Parameter: Name|Name]] for the new route
* Select a '''protocol variant'''
* Select a [[Parameter: Protocol Type|Protocol Variant]]
* Select a '''replicant mode'''
* Select a [[Parameter: Replication Mode|Replication Mode]] (ANSI96 and TELCORDIA variants)
* Select an '''SLS mask''' (this is only for ANSI and TELCORDIA protocol variants)
* Select an [[Parameter: SLS Mask|SLS Mask]] (ANSI and TELCORDIA protocol variants)
* Select a '''destination point code (DPC)'''
* Select a [[Parameter: Destination Point Code|Destination Point Code]] for this route
* Click '''Create'''
* Click '''Create'''


Line 24: Line 26:
[[Image:Toolpack_v2.5_SCCP_Route_Created.png]]
[[Image:Toolpack_v2.5_SCCP_Route_Created.png]]


4- Configure [[SCCP Route Backup Point Code]]
* Assign [[Parameter: SCCP Backup Point Code| Backup Point Codes]] to use in case this route's [[DPC]] is not available. 
[[Image:SCCP_Route_Backup_PC.png]]
* '''Note: For each selected point codes, a valid SCCP route must exist'''.
5- '''Next Step:''' [[Toolpack_v2.5:Creating_an_SCCP_SSN|Create an SCCP SSN]]


==List of Parameters==
==List of Parameters==
Line 29: Line 40:
* [[Parameter: Name|Name]]
* [[Parameter: Name|Name]]
* [[Parameter: Protocol Type|Protocol Variant]]
* [[Parameter: Protocol Type|Protocol Variant]]
* [[Parameter: Replicant Mode|Replicant Mode]]
* [[Parameter: Replication Mode|Replication Mode]]
* [[Parameter: SLS Mask|SLS Mask]] (For ANSI and TELCORDIA variants only)
* [[Parameter: SLS Mask|SLS Mask]] (For ANSI and TELCORDIA variants only)
* [[Parameter: Destination Point Code|Destination Point Code]]
* [[Parameter: Destination Point Code|Destination Point Code]]
==Navigation==
{| class="wikitable"
|-
! Previous !! Next
|-
| [[Toolpack_v2.5:Creating_an_SCCP_LSAP|Create an SCCP LSAP]] || [[Toolpack_v2.5:Creating_an_SCCP_SSN|Create an SCCP SSN]]
|}

Latest revision as of 13:37, 26 September 2014

Applies to version(s): v2.5, v2.6, v2.7

Now that you have created an SCCP LSAP, you must create a new SCCP route for your system. This step in the Web Portal configuration exists to create a route to a specific destination point code (DPC).

To Create an SCCP Route:


1- Click Create new Sccp Route in the SCCP LSAP configuration window

Toolpack v2.5 Create SCCP Route.png

2- Configure the new SCCP Route:

Toolpack v2.5 Creating SCCP Route.png

3- Verify that the "SccpRoute was successfully created" message appears

Toolpack v2.5 SCCP Route Created.png

4- Configure SCCP Route Backup Point Code

SCCP Route Backup PC.png

  • Note: For each selected point codes, a valid SCCP route must exist.


5- Next Step: Create an SCCP SSN

List of Parameters

Navigation

Previous Next
Create an SCCP LSAP Create an SCCP SSN