Actions

Difference between revisions of "Toolpack:Adding an Adapter C"

(Fix typo: Is -> In)
 
(2 intermediate revisions by the same user not shown)
Line 11: Line 11:
 
'''To add a hardware device:'''
 
'''To add a hardware device:'''
  
1- Click '''Hardware''' in the navigation panel
+
1- Click '''Hardware Units''' in the navigation panel
  
  
Line 17: Line 17:
  
  
2- Click '''Create New Hardware''', to add a new hardware device
+
2- Click '''Create New Units''', to add a new hardware device
  
  
Line 28: Line 28:
 
* Select the appropriate '''hardware device''' from the Type field. (In this case select TMP)
 
* Select the appropriate '''hardware device''' from the Type field. (In this case select TMP)
 
* Select the type of TDM lines that the hardware device will support.
 
* Select the type of TDM lines that the hardware device will support.
* Indicate if the device will operate as a backup in a 1+1 configuration. If this is the first device being added, leave this field clear.
+
* Indicate if the device will operate as a backup in an N+1 configuration. If this is the first device being added, leave this field clear.
* Provide the amount of time is seconds, that the system will wait for calls to complete before shutting down for an upgrade.
+
* Provide the amount of time in seconds, that the system will wait for calls to complete before shutting down for an upgrade.
 
* Enter the location in which the hardware device is installed.
 
* Enter the location in which the hardware device is installed.
 
* Enter a meaningful description as to the usage or purpose of the hardware device.
 
* Enter a meaningful description as to the usage or purpose of the hardware device.
Line 39: Line 39:
  
 
'''NOTE'''  
 
'''NOTE'''  
The following image shows the 1+1 Backup field set. This is done for the addition a secondary TMP that will operate as the designated 1+1 backup in a 1+1 Group.
+
The following image shows the N+1 Backup field set. This is done for the addition of a secondary device that will operate as the designated 1+1 backup in a 1+1 Group.
  
 
[[Image:Hardware_3.png]]
 
[[Image:Hardware_3.png]]

Latest revision as of 15:11, 27 May 2015

Applies to version v2.7

When you receive a new system, at least one hardware configuration will have been set in the Toolpack application server, by default. To add other hardware devices, you must use the Tmedia Web Portal.

Schematic showing 2 TMP6400 devices with an external server and a second machine with a web browser

To add one or more additional hardware devices to the Toolpack system configuration, their serial numbers must be registered with the Toolpack application server.


To add a hardware device:

1- Click Hardware Units in the navigation panel


Hardware 0.png


2- Click Create New Units, to add a new hardware device


Hardware 1.png


3- Enter a name for the hardware device

  • Enter the serial number of the new hardware device (filling in the Serial Number field will cause auto-completion of the field to occur).
  • Select the appropriate hardware device from the Type field. (In this case select TMP)
  • Select the type of TDM lines that the hardware device will support.
  • Indicate if the device will operate as a backup in an N+1 configuration. If this is the first device being added, leave this field clear.
  • Provide the amount of time in seconds, that the system will wait for calls to complete before shutting down for an upgrade.
  • Enter the location in which the hardware device is installed.
  • Enter a meaningful description as to the usage or purpose of the hardware device.
  • Select Enabled from the Target State field.
  • Click Create


Hardware 2.png

NOTE The following image shows the N+1 Backup field set. This is done for the addition of a secondary device that will operate as the designated 1+1 backup in a 1+1 Group.

Hardware 3.png

4- Verify that the "Adapter was successfully created" message appears, and that the newly added hardware device appears in the Hardware List below


CreateHardwareTmp 3 A.png

List of Parameters