Actions

FreeSBC Troubleshooting: Difference between revisions

Line 120: Line 120:
<pre>SBC -&gt; Advanced parameters
<pre>SBC -&gt; Advanced parameters
</pre>
</pre>
* For Two-way no audio, sometimes phone/phone system is behind the firewall, user may find that if they just establish the call, two-way audio is fine, but if the call is placed on hold for certain time, and when resuming the call, there is no more two-way audio. This could be due to the the external firewall is set to shutdown the RTP path after certain time of being idle (silence) as in the case of call on hold. The solution is to optimize this setting at external firewall to prevent it from shutting down the RTP over a reasonable or defined time.
* For Two-way no audio, sometimes phone/phone system is behind the external firewall, user may find that if they just establish the call, two-way audio is fine, but if the call is placed on hold for certain time, and when resuming the call, there is no more two-way audio. This could be due to the external firewall is set to shutdown the RTP path after certain time of being idle (silence) as in the case of call on hold. The solution is to optimize this setting at external firewall to prevent it from shutting down the RTP over a reasonable or defined time.


= Call Drops Problems =  
= Call Drops Problems =  

Revision as of 23:34, 3 January 2021


Scheduling Problems

You may see the SBC tab in the general status as yellow. When you select it:

Status -> SBC

You may see “Scheduling problem sbc list” with the hostname of the FreeSBC. If you select it, you may see “Scheduling problem alarm” set to “true”
Status containing “scheduling” problem may point to:

  • Non-dedicated (or not ‘pinned’) CPU [Open-stack]
  • Not enough CPU reservation [Vmware]
  • Memory is not dedicated to the Virtual Machine (VM)
  • Too many active virtual machines fighting for resources on the host
  • On KVM based installations (proxmox,virtmanager) CPU type must set to “host”

You need to be sure other VMs are not taking resources from FreeSBC VM instance. Follow requirements shown here: FreeSBC requirements

SBC Status.png

Registration Errors

Endpoint sends the register request to FreeSBC however the FreeSBC is not forwarding it to the registrar

  • Check if SIP domain configured correctly

Creating a SIP domain

  • Check the SIP domain Status. Be sure domain registrar can be reached by FreeSBC
 Go to Status -> SIP -> SIP Domain -> Status -> SIP Registration Domains
  • Check if SIP client sends correct Domain name to FreeSBC. You can capture a SIP trace (see Signaling trace capture tool ) and use Wireshark to analyze the trace. Look at the “To:” SIP header: it must match what is in the Sıp Domain configuration of the FreeSBC.

FreeSBC forwards incoming registration messages to the registrar but registrar returns an error

  • Check if SIP domain configured with correct registrar setting

Creating a SIP Registrar

  • Check if Registrar NAP configured with a correct IP address

Allocating a SIP NAP

  • Check if your client configured with the correct username and password
  • Check the forwarding modes on FreeSBC, and select the correct one

Forwarding Modes

FreeSBC always modifies the contact URI in SIP register requests to remain on the path between SIP User Agents and registrars. FreeSBC supports two different SIP registration forwarding modes (i.e. "Contact Remapping" or "Contact Passthrough").

  • The "Contact Passthrough" forwarding mode makes the contact username portion of the Contact URI in SIP register requests to pass through unchanged.
  • The "Contact Remapping" forwarding mode modifies the contact username portion of the Contact URI in SIP register requests and make it unique.

Forwarding Modes.png

Forward original headers from incoming request

If your registrar wants to receive original headers from incoming requests, Forward the domain without any modification in From/To/Contact/P-Asserted-Identity SIP headers. If you want to forward incoming SIP from/to header domain to the outgoing leg you need to upgrade your FreeSBC to the minimum Release 3.0.114. With Release 3.0.114 we added forward_sip_domain script to our routing scripts.

This filter is used to forward the domain name (or IP address and port) from the incoming call to the outgoing call, for the following SIP headers:

  • from (update call attribute :calling by appending :calling_sip_host and calling_sip_port)
  • to (update call attribute :called by appending :called_sip_host and called_sip_port)
  • P-asserted-identity (update call attribute :private_address by appending :private_address_sip_host and private_address_sip_port)
  • To set up a Filter, the main script needs to be modified. The main script can be either simple_routing.rb, or any other script.

First, go to the routing script section of the Web portal

Gateway -> Routing scripts -> Example Scripts -> simple_routing.rb [Edit]

Three things need to be added. At the start of the script:

require 'forward_sip_domain' unless defined?(ForwardSipDomain)

In the main class:

include ForwardSipDomain
route_remap :method => :forward_sip_domain


The final script will look like this (with possibly other filters also included):

require 'base_routing'
require 'forward_sip_domain' unless defined?(ForwardSipDomain)

class SimpleRouting < BaseRouting
  include ForwardSipDomain
  
  route_match :call_field_name => :called
  route_match :call_field_name => :calling
  route_match :call_field_name => :private_address
  
  route_match :call_field_name => :nap
  route_remap :call_field_name => :called, :route_field_name => :remapped_called
  route_remap :call_field_name => :calling, :route_field_name => :remapped_calling
  route_remap :call_field_name => :private_address, :route_field_name => :remapped_private_address
  route_remap :call_field_name => :nap, :route_field_name => :remapped_nap
  route_remap :method => :forward_sip_domain
  

end
  • This script requires the routes to have a custom column named "forward_sip_domain", type boolean.
Gateway -> Routes -> Create New Route Column

Name: forward_sip_domain
Type attributes: boolean

See FreeSBC uses case: Remote Workers

Note: This script is coming as default after Rls. 3.0.116. You just need to set the forward_sip_domain route column as enabled.

One Way Audio/ No Audio Problems

  • Can place a call, but one way or no audio

One-way audio is a common VOIP problem. It is one of the most frequent support questions we receive. There are many possible causes;

  • Outdated firmware in routers, VOIP phones, Firewalls, etc. can cause one-way audio. Ensure you have the latest updates for all the devices in the call path.
  • Firewall mistakenly blocking RTP, be sure firewalls configured correctly.
  • Particularly if Network Address Translation (NAT) is involved in the call path, configuration of the various devices may be a problem. Please check the link for NAT
  • Another reason for one way audio is having your system set to offering unsupported codecs within your other SIP systems.
  • Just as each side of a call must send RTP within the same codec, each side must also have the same phase timing (or ptime value). See SDP Description
  • Configured RTP port ranges can cause a problem too. Check FreeSBC and endpoints (Clients, SIP Trunks) are using correct RTP ports. See Creating an IP Port Range
  • High one-way packet loss. If sufficient packet loss occurs in one direction on a call, that half of the conversion may break down, but not cause the entire call to drop. Packet loss can occur due to a number of reasons:
    • High utilization on a link with no QoS.
    • Misconfigured interface: Half-duplex or duplex mismatch.
    • Underperforming network devices.
    • Cabling faults.
  • Wrong threshold configuration under SBC Advanced parameter can cause FreeSBC to block RTP-Audio by the firewall due to thresholds. You can see the following error in your call trace;

Data path errors.png
Please double check your thresholds configuration from;

SBC -> Advanced parameters
  • For Two-way no audio, sometimes phone/phone system is behind the external firewall, user may find that if they just establish the call, two-way audio is fine, but if the call is placed on hold for certain time, and when resuming the call, there is no more two-way audio. This could be due to the external firewall is set to shutdown the RTP path after certain time of being idle (silence) as in the case of call on hold. The solution is to optimize this setting at external firewall to prevent it from shutting down the RTP over a reasonable or defined time.

Call Drops Problems

My call dropped while I was talking, I might hear fast busy or just dead air.

  • Call dropping within the first minute – missing ACK in Invite. Check the NAT configuration. NAT
  • Maximum Call time exceeded. Many service providers set a limit on the maximum duration for any call passing through their system. Double-check with your service provider.

Calls dropping at specific intervals (10 minutes, 30 minutes)

    • Check the SIP session timers. [[SIP_session_timers|SIP Session timers]
    • Uncheck “Use Session Timer” from SIP configuration. SIP -> Select the name from SIP Configuration menu -> Session Timers

Session timers.png

  • Call dropping within the first minute – missing ACK in Invite. Check the NAT configuration. NAT
  • Maximum Call time exceeded. Many service providers set a limit on the maximum duration for any call passing through their system. Double-check with your service provider.

Calls dropping because of Congestions

The calls can be dropped because of the congestion too. You can check the NAP status for congestions.

Congestion.png

If you are receiving a congestion error,

  • You first need to check the concurrent call counts. If your concurrent call count exceeded the license, you would have a congestion error. Please check your license.
  • Check if you set any Call Rate Limiting in the NAP. Go to NAPS -> Select The NAP -> Advanced Parameters -> Call Rate Limiting
  • For other congestion problems please contact support@telcobridges.com

Sub-optimal config sbc list warning

The reason for this is that some Nics (Azure, vmxnet3, e1000, ixgbe vf) report a RETA size of 0 while reporting multiple rx queues, meaning they can not support multiple CPUs. However TBRouter is not aware of this limit on those Nics then initiate the Cores on the Nics

Please check the following link for how to solve this issue Toolpack: How to Get Rid of Sub Optimal

Log procedure for Signaling/Routing problems

  • Set trace levels to 1 using by tbx_cli_tools_remote command
    • Connect to ssh and use tbx_cli_tools_remote command
    • Select the application
    • Set the trace level to 1 by typing "T"
    • When you finished the test call please disconnect from the application, press Escape twice.
    • Do this for the gateway, tbsyslog, toolpack_engine applications.
    • You can get more detail about how to use tbx_cli_tools_remote from the following link How_to_use_tbx_cli_tools_remote_program
  • Run tbsigtrace capture. For more details please check the following link Toolpack_Debug_Application:Tbsigtrace
  • Make a test call or simulate the problem
  • Stop the tbsigtrace capture
  • Export the call trace. For more details please check the following link Toolpack:Retrieving_Call_Trace_C
  • Generate a tbreport for the date/time you made the test call For more details please check the following link TBReport

Log procedure for Voice/RTP problems

  • Set trace levels to 1 using by tbx_cli_tools_remote command
    • Connect to ssh and use tbx_cli_tools_remote command
    • Select the application
    • Set the trace level to 1 by typing "T"
    • When you finished the test call please disconnect from the application, press Escape twice.
    • Do this for the gateway, tbsyslog, toolpaack_engine, and tbrouter applications.
    • You can get more detail about how to use tbx_cli_tools_remote from the following link How_to_use_tbx_cli_tools_remote_program
  • Run tbrouter capture. For more details please check the following link VoIP_Ethernet_Capture_FreeSBC_A
  • Make a test call or simulate the problem
  • Stop the tbrouter capture
  • Export the call trace. For more details please check the following link Toolpack:Retrieving_Call_Trace_C
  • Generate a tbreport for the date/time you made the test call For more details please check the following link TBReport